Catalog excerpts
Digital Precision Oil Tester DPOT ™ WATER IN OIL ANALYZER FOR LUBRICATING OILS, FUEL OILS AND SOLVENTS The new DPOT™ from GESERCO is the most advanced and innovative water in oil analyzer to be developed by the Number 1 Expert in rapid condition monitoring of oils in service. DPOT™ is based on the ‘’Aquatest’’ water in oil analysis method which is standardized by ISO (1),AFNOR (2) and GFC (3) and which was continuously refined by GESERCO over the past 40 years. Standard ISO 9114: 1997 | (2) Standard NF T60-640 June 2018 | (3) Method GFC TR-40-A-
Open the catalog to page 1Digital Precision Oil Tester – DPOT™ WATER IN OIL ANALYZER FOR LUBRICATING OILS, FUEL OILS AND SOLVENTS Applicable to any type of lubricating oils and fuel oils (mineral, synthetic or bio-generated), solvents, alcohols, aromatic liquids, greases… No interference of the lubricant additives on the analysis result, even when the proportion of additives is massive Digital result delivered in water volume or water mass within 90 seconds 8 measuring ranges from 0 – 2000 ppm H2O to 0 – 15 % H2O Works with very small test samples down to 0.5 cc No hazardous chemicals for transportation, nor...
Open the catalog to page 2Digital Precision Oil Tester – DPOT™ WATER IN OIL ANALYZER FOR LUBRICATING OILS, FUEL OILS AND SOLVENTS PREDICTIVE TEST MODE: Result within 90 seconds! • The predictive measurement mode of DPOT™ is built on several tens of thousands of water in oil analyses produced by GESERCO over the past 40 years. • When in predictive test mode, DPOT™ monitors carefully the release of water from the sample as well as the test profile. After a few tens of seconds of integration, the DPOT™ algorithm is able to predict the final water content of the sample with an accuracy better than ±10%. After a few...
Open the catalog to page 3Digital Precision Oil Tester – DPOT™ WATER IN OIL ANALYZER FOR LUBRICATING OILS, FUEL OILS AND SOLVENTS Metrological Specifications MEASURING RANGE Resolution: 5 levels from 1 ppm H2O to 1 %H2O Engineering units: H2O volume, %H2O mass, ppmH2O volume, % ppmH2O mass Time to test result: Down to 90 seconds in predictive mode 4 end of test modes: (1) utomatic end of test detection with user a defined criterion Test principle: Aquatest (2) tandardized test duration (15 minutes) s Test reagents: eagent WT or Reagent WT/NH (2), R solvent WT2 (2). (3) ser defined test duration (up to 3 hours) U 2...
Open the catalog to page 4All GESERCO catalogs and technical brochures
-
Water in Oil + BN Test Kit
2 Pages
-
STM 1 Test Kit
1 Pages
-
H2S Test Kit
1 Pages
-
Density Measurement
1 Pages
-
CompaTest™ Kit
1 Pages
-
Soot Test kit
2 Pages
-
Bacteria Test Kit
1 Pages
-
Biocide TotalFuelWash
1 Pages
-
GESERCO Products Catalogue
60 Pages
-
TAN Test
1 Pages
-
POLLUVISION™ Test Kit
1 Pages
-
CE™ Test Kit with ROTG
2 Pages
-
CLM
2 Pages
-
BN Test
2 Pages
-
GOTest™
1 Pages
-
CM1
2 Pages
-
LubTest Professional™
2 Pages
-
LubTest Premium™
2 Pages
-
Tan + BN Test Kit
1 Pages
-
EVI
2 Pages
-
CEVM Test Kit
2 Pages
-
Viscobille™ VCD - ViscoTest™
1 Pages
-
Sampling Mini Kits
1 Pages
-
Sampling kit
1 Pages
-
WaterTest™ Kit
2 Pages
-
FlashTest™
1 Pages
-
CoolTest™
1 Pages
-
Solvent DP
2 Pages
-
Solution WT2
2 Pages
-
Reagent WT/NH
1 Pages
-
Reagent WT
1 Pages
-
Aviation WaterTest
1 Pages
Archived catalogs
-
MFTest Premium
1 Pages
-
MFTest Premium
1 Pages