Tial Convertisseur de temperature montage rail DIN - Entree PtIOO Temperature converter DIN rail mounting - RTD100 input i Fonction Convertisseurs de temperature Tial destines a la conversion du signal issu d'une sonde Pt100 en un courant 4/20mA. Montage sur rail DIN. Installables en zone explosible (C.F. codification). J Caracteristiques electriques Entree capteur Pt100 2 ou 3 fils selon EN60751 Etendue de mesure max. -220°C a 850°C Gamme minimale 10°C Sortie 4/20 mA Alimentation Modele standard 8V ... 30 Vcc Version ATEX 8V ... 28 Vcc selon la valeur maximale Resistance de charge (Valimentation-8) / 0,0215 0 Detection de rupture de sonde ou de court circuit : Configurable 3,5 mA ou 21,5 mA NAMUR NE 43 Haut d'echelle 21,5 mA NAMUR NE 43 Bas d'echelle 3,5 mA Temps de chauffe 5 minutes Temps de reponse < 2 secondes Derive Tension d'alimentation : <0,01% du courant de boucle pour une variation de 0,1% de la tension d'alimentation Temperature : < 10% de la precision / degre Erreur due a la resistance de ligne : Pt100 2 fils 2,5°C/ 0 compensable par configuration Pt100 3 fils 2,5°C/ 0 de desequilibre entre fils i Function Tia1 temperature converters aimed at converting signals from RTD100 sensor to a standard 4 to 20mA current signal. Din rail mounting product. Certified to be installed in hazardous area (See codification). j Electrical data Input RTD100 2 or 3-wires according to EN60751 Max measuring range -220 to 850°C Minimum span 10°C Output Power supply Standard model ATEX version Accuracy 4/20 mA 8V ... 30 Vdc 8V ... 28 Vdc < 0.1% F.S. or < 0.5°C according to the maximal value (Vsupply-8) / 0.0215 0 Load resistance Shorted or broken line detection: Configurable 3.5 mA to 21.5 mA NAMUR NE43 Upscale 21.5 mA NAMUR NE43 Downscale 3.5 mA Warm-up time 5 minutes Drift Voltage supply: < 0.01% of the current in the loop for a variation of 0.1% of Vsupply Temperature: < 10% of accuracy / degree Line resistance effect 2-wires RTD 2.5 °C / 0, compensation is configurable Mechanical data Presentation Protection Masse T° d'utilisation T° de stockage Humidite relative Raccordement Taille maxi des fils BoTtier polycarbonate l = 13 mm, h = 110 mm, p = 110 mm IP 20 approx. 200 g. -40°C a +85°C (modeles NON ATEX) -40°C a +85°C 5% a 95% sans condensation. Bornes a visser demontables de 1x0,2 mm2 a 1x2,5 mm2 Housing Protection Weight Working T° Storage T° Relative humidity Connection Max. wire size Polycarbonate l = 13 mm, h = 110 mm, p = 110 mm IP 20 approx. 200 g -40°C to 85°C (non ATEX version) -40°C to 85°C 5% to 95% without condensing Removable screw terminals from 1x0,2 mm2 to 1x2,5 mm2 Concernant les produits ATEX et lECEx : Securite Intrinseque EN 60079-0 & CEI 60079-0 EN 60079-11 & CEI 60079-11 EN 60079-26 & CEI 60079-26 N° d'attestation INERIS 13ATEX0015X & INE13.0022X For ATEX and IECEx products: Intrinsic Safety EN 60079-0 & IEC 61241-0 EN 60079-11 & IEC 60079-11 EN 60079-26 & IEC 60079-26 Certificate N° INERIS 13ATEX0015X & INE13.0022X Classement IECEx / IECEx Classification ^BParametres ATEX de securite / ATEX safety parameters Parametres d'entree / Input parameters Entre les bornes / Between terminals «1» & «2» U. I. P. C L Nota : Le cable d'alimentation du Tia1 ne doit pas exceder une inductance de 20mH. The supplying cable of the Tia1 must have a maximum inductance of 20mH. Parametres de sortie / Output parameters Entres les bornes / Between terminals «3», «4», «7» & «8» I u; i; p; c L~ FC-Tial-FREN-29-03-2013 Subject to modifications due to technical advances / Soucieux d'ameliorer nos produits, nous nous reservons le droit de reviser sans preavis les caracteristiques de nos produits

Tial Convertisseur de temperature montage rail DIN - Entree PtIOO Temperature converter DIN rail mounting - RTD100 input Raccordement typique / Typical wiring Type de protection Method of protection 2 ways of configuration are possible: - With ProgressXmanager Software - With FDT/DTM These programming supports (ProgressXmanager, CommDTM GEORGIN and DTM Tial) are available on our web site. Product configuration must be done in SAFE AREA and not connected to a probe in hazardous area. Connection to the computer must be done with the TiX'link serial interface series. Configurable parameters: - TAG...