Lighting control
66Pages

ADAPTABILITY IN LIGHTING CONTROL

Adaptability in Lighting Control

A Gentec's Kameleon Serie offers a wide range of solutions to suit any lighting control requirement. From the field programmable K4 Series for small to medium size applications to the K6 (BACnet) and K8 (LON) Series with their configuration and visualisation software and their dimming capability. This System Design Guide provides general guidance regarding lighting control sequences and applications in commercial and institutional buildings. Furthermore, engineers, electrical contractors and property managers will find all the necessary information on how to design a Kameleon system...

Common Control Sequences COMMON CONTROL SEQUENCES System Design Guide The following section – control sequences, describes the most commonly used lighting control sequences in a commercial building. TIMED SCHEDULES The sweep ON/OFF Operation is used to turn preset lights ON and OFF automatically according to pre-programmed schedules*. To permit off-hours activities, such as overtime and janitorial work, scheduling can be overridden through different actions such as manual ON/OFF and motion detection. TYPICAL APPLICATIONS * The schedule programming is performed directly on the KC-411 8...

Common Control Sequences System Design Guide CLEANING/SECURITY* Enabled during off-work hours, the Cleaning/Security Function will allow authorized employees (janitor, guard, landlord, etc.) to switch the lights ON/OFF in preset areas without disturbing the occupants. The Cleaning/Security Function is generally performed through the use of key switches. When the key switch is activated, the system memorizes the current status of all the relays in the area. An ON activation of the key switch will turn ON all the OFF relays in the area. The OFF activation of the key switch will only turn OFF...

Typical Applications The following section – typical applications, presents the most commonly used control sequences inside commercial buildings. For each application, the required lighting control components are listed. COMMON CONTROL SEQUENCES System Design Guide • K6 or K8 Series Panels • Low Voltage Switches with Pilot LEDs • Key Switches • Motion Detectors • Constant Light Controllers • Exterior Photocell • Kameleon Software (K8) • Link to the Building Management System** • Dimming Controllers* *If centralized dimming control is required ** Optional SYSTEM COMPONENTS SYSTEM...

kameleon System Design Guide DPTAII STORES SYSTEM COMPONENTS SYSTEM CONFIGURATION TYPICAL APPLICATIONS COMMON CONTROL SEQUENCES

Typical Applications SYSTEM COMPONENTS SYSTEM CONFIGURATION TYPICAL APPLICATIONS COMMON CONTROL SEQUENCES

Kameleon Lighting Control Systems offer highly customizable configurations that are designed to fully adapt to the occupants, as well as providing cost-savings opportunities to the owners. In its efforts to provide a solution for all types of needs, Gentec R&D Team has been developing three complementary systems: the K4, K6 and the K8-Series. SYSTEM'S FEATURES Relay Panels Capacity Two-Wire, 20a, H.I.D., 1 Pole, Latching Relay Two-Wire, 20a Plug-In Relays, 1 Pole, Latching Relay Two-Wire, 20a, H.I.D., Breaker-Relay, Latching Relay On-Site Programmable Time Clock On-Site Group...

APPLICATIONS TYPIQUES SÉQUENCES DE CONTRÔLE COURANTE

GENERAL DESCRIPTION • Practical design offering easy installation and high efficient running • Standard sizes for 8, 16 & 32 relays • Removable hinged door with key lock • Box knockouts are located on both side of the enclosure to facilitate wire and conduit entries • Panel and back panel accept 20 A HID heavy relays as well as electronic cards c/w wiring duck • Line voltage compartment c/w cover plate • Panel comes with transformer & supply terminal block APPLICATION Small to medium size buildings controlled via a field programmable controller KC-401 and KC-411 astronomical clock; schools;...

K4 Relay Panels SURFACE MOUNT ENCLOSED SYSTEM COMPONENTS SYSTEM CONFIGURATION TYPICAL APPLICATIONS COMMON CONTROL SEQUENCES FLUSH MOUNT ENCLOSED SURFACE MOUNT ENCLOSED FLUSH MOUNT ENCLOSED Height Wide Deep Height Wide Deep inches mm inches mm inches inches inches mm inches mm inches mm ORDERING INFORMATION S 4 = Mounting Type Surface (S) / Flush (F) 1 5 = Type 1, 2, 3R, 4X MODEL RELAYS CAPACITY TYPE K4-8RP-S1 8 □ S 2625, Dalton Avenue, Quebec QC G1P 3S9 Canada / 418.651.8000 / gentec.ca

GENERAL DESCRIPTION • Field Programmable Relay Controller • 16-Output (20 A HID Relay Controller) • Up to 4 groups (zones) Configuration • 2 controllers can be networked and therefore controls up to 32 relays and 8 groups • Multi-Group Relay Assignment Capability • Real Time System Status Feedback • Provided Through Different LED Patterns • Membrane Keypad • Push-Button Switch Tone • Multiple Input Combination (4 devices): ■ low Voltage 2-Wire Switch ■ dry Contact ■ occupancy Sensor ■ time Clock ■ photocell ■ light Level Controller • Energy Codes Certified Features: ■ timed Schedules (when...

KC-401 Relay Controller SYSTEM COMPONENTS SYSTEM CONFIGURATION TYPICAL APPLICATIONS COMMON CONTROL SEQUENCES ORDERING INFORMATIONPART NUMBER KAMELEON SERIES RELAY CONTROLLER K4 SERIES 35459-01 KC -40139691-01 Complete Kit 2625, Dalton Avenue, Quebec QC G1P 3S9 Canada / 418.651.8000 / gentec.ca

GENERAL DESCRIPTION • Field Programmable Time Clock Controller • 8 Outputs (Channels or Relays) • Up to 2-group (zone) Configurations • A KC-411 can be networked with a KC-401 • Relay Controller • Multi-Group Relay Assignment Capability • LCD Display (4 Lines - 20 Characters) • Membrane Keypad • Push-Button Switch Tone • Palm Pilot Programming/Operation Capabilities (IRDA) • Multiple Input Combination (2 devices): ■ low voltage 2-Wire Switch ■ dry contact ■ occupancy sensor ■ switch ■ photocell ■ light level controller • Photocell Dedicated Input (2) (Resistive AnalogInput) • Daylight...