Flat heaters type F Installation on the side or at the bottom (small side) (large side) Universal model for all types of installation such as side of tank, bottom of tank with feet or on slidings. Rigid structure ideal for important powers. Assembly type convenient for immersion heaters with reference P30 (thickness 30 mm) , P40 (thickness 40 mm) , P90 (thickness 100 mm) This modular assembly type provides a satisfactory installation of the heaters in all situations. The cable is rolled up according dimensions & shapes proposed and held with PVDF, PP or FEP strips which ensure the right distance between the rolls. To secure completely the heating part it is then mounted on a rigid rod structure in PVDF or PP. The heater is secured on the rod structure by clips which, whenever needed, make the removal of the heating part easier. Warning : The reference table of the flat heaters (next pages) does not give the overall dimensions of the F range assembly type : 85 mm ±10 mm must be added to each length and width. Options and Accessories Extra length of cables Electrical connecting cable C of type H05 VV-F (PVC) or H07 RN-F (Neopren) Non heating cable N to go out of the tank Electric safety : the Galvatherm heater complies with protection class 1 of EN 60519-1/2. The cable is screened throughout the entire length by a copper earthing strip. The earthing must be connected to the earth. In order to provide maximum safety, a fault-current (FI) protection device (30mA) should be used. On a rigid plastic rod frame Ø20 mm, PVDF or PP The Galvatherm heater is only planned to heat liquids. Removable guard Perforated plastic guard PP ou PVDF Ref in PP : PRPPP Ref in PVDF : PRPPF Feet for type A Standard height 50 mm Other heights possible For installation at the bottom of the tank. Ref in PP : PIPP Ref in PVDF : PIPF Ref in PTFE : PIPTFE Allow between 200 to 300 mm extra on the H length (H=installation height on N) Ref in PP : PEPP Ref in PVDF : PEPF Frame supports PP or PVDF, to fix on the edge of the tank Réf in PP : SUPP Réf in PVDF : SUPF GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnières, France www.galvatek.com - Tél. 01 30 93 07 57 Fax. 01 30 93 25 04 - [email protected]

The table below informs on the dimensions of the heating part and its references. The reference number begins by P30, P40 or P90. These codes indicate the thickness 's device. P30 = thickness 30 mm / P40 = 40 mm / P90 = 100 mm All dimensions are given with a tolerance of ± 10 mm. Standard cable coating : FEP single layer. For other coatings please contact us. List of other single-phase voltages available • 110V single-phase : 0.5 kW, 1 kW, 1.5 kW, 2 kW • 460V single-phase : 1 kW, 1.5 kW, 2 kW, 3 kW, 4 kW, 5 kW, 6 kW [rJaH GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnieres,...

For the construction of the reference, see following page. Attention P90 type F : Add 25 mm on J and K to the dimensions written If feet option : 6 feet required instead of 4 Other voltage available : 460V three-phases : 3 kW, 4.5 kW, 6 kW, 9 kW, 12 kW, 15 kW [rJaH GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnieres, France www.galvatek.com - Tel. 01 30 93 07 57 Fax. 01 30 93 25 04 - [email protected]

code code power code voltage code exit code cable code code code code J = small side K= large side Cable code details F = FEP single layer 1 W/cm2 G = FEP double layer 1 W/cm2 P = PFA single layer 1 W/cm2 D = PFA double layer 1 W/cm2 F = with a rod frame H = for rod frame PVDF PP PVDF PP inox PVDF PP FEP FEP FEP other pieces PVDF PP PVDF PP PP GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnieres, France www.galvatek.com - Tel. 01 30 93 07 57 Fax. 01 30 93 25 04 - [email protected]