Galvatherm® - Flat heaters, type F for frost protection
4Pages

{{requestButtons}}

Catalog excerpts

Galvatherm® - Flat heaters, type F for frost protection - 1

Flat heaters type F, for fost protection Rigid structure ideal for important powers With options Feet & Cable-gland these models are specifically adapted to keep liquid storage tanks from freezing, all sizes with or without double wall. Installation through the inspection trap (ø 500 mm minimum). Can be installed in a tank filled when support feet are ordered on each side of the heating part. Can be passed through the inspection trap without interfering with the tank. For a complete efficiency we recommend a cable-gland installed on the non heating part N - positioning hole ø 75 mm to be planned on the dome - and a FEP Teflon® coated PT100 probe mounted on heater. Length H corresponds to the installation height of the cable-gland on the N part. To ensure a proper positioning and avoid any mechanical damage of the cable, please allow an extra 300 mm on the H length. The cable is rolled up according dimensions & shapes proposed and held with PVDF, PP or FEP strips which ensure the right distance between the rolls. To secure completely the heating part it is then mounted on a rigid rod structure in PVDF or PP or on a stainless steel structure. Electric safety : the Galvatherm heater complies with protection class 1 of EN 60519-1/2. The cable is screened throughout the entire length by a copper earthing strip. The earthing must be connected to the earth. In order to provide maximum safety, a fault-current (FI) protection device (30mA) should be used.. Options and Accessories Extra length of cables Electrical connecting cable C of type H05 VV-F (PVC) or H07 RN-F (Neopren) Non heating cable N to go out of the tank The Galvatherm heater is only planned to heat liquids. Removable guard Perforated plastic guard PP ou PVDF Ref in PP : PRPPP Ref in PVDF : PRPPF Cable-gland Ø75 mm Feet (standard 100 mm) PP, PVDF or stainless steel for installation at fthe bottom Ref in PP : PIPP Ref in PVDF : PIPF Ref in stainless steel : PIIN (additional ballast possible) Allow between 200 to 300 mm extra on the H length (H=installation height on N) Ref in PP : PEPP Ref in PVDF : PEPF Teflon®coated PT100 probe 2,3 or 4 wires, installed at the factory. Closed tank : the probe goes through the same cablegland as the one of the heater. Fixed by PP or Tefzel clamps Ref : contact us GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnières, France www.galvatek.com - Tél. 01 30 93 07 57 Fax. 01 30 93 25 04 - info@galvatek.fr

Open the catalog to page 1
Galvatherm® - Flat heaters, type F for frost protection - 2

Flat heaters, reference numbers The table below informs on the dimensions of the heating part and its references. The reference number begins by P30, P40 or P90. These codes indicate the thickness ‘s device. P30 = thickness 30 mm / P40 = 40 mm / P90 = 100 mm All dimensions are given with a tolerance of ± 10 mm. Standard cable coating : FEP single layer. For other coatings please contact us. SINGLE-PHASE IMMERSION HEATERS 230V sg-ph List of other single-phase voltages available • 110V single-phase : 0.5 kW, 1 kW, 1.5 kW, 2 kW • 460V single-phase : 1 kW, 1.5 kW, 2 kW, 3 kW, 4 kW, 6 kW...

Open the catalog to page 2
Galvatherm® - Flat heaters, type F for frost protection - 3

Flat heaters, reference numbers THREE-PHASES IMMERSION HEATERS JxK For the construction of the reference, see following page. Attention P90 type F : Add 25 mm on J and K to the dimensions written * If feet option : 6 feet required instead of 4 Other voltage available : 460V three-phases : 3 kW, 4.5 kW, 6 kW, 9 kW, 12 kW, 15 kW GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnières, France www.galvatek.com - Tél. 01 30 93 07 57 Fax. 01 30 93 25 04 - info@galvatek.fr

Open the catalog to page 3
Galvatherm® - Flat heaters, type F for frost protection - 4

Flat heaters, codification Construction of the reference number P30 thickness code power code voltage code exit code cable code assembly code materials code J = petit côté K = grand côté Cable code details F = FEP single layer 1 W/cm2 G = FEP double layer 1 W/cm2 P = PFA single layer 1 W/cm2 D = PFA double layer 1 W/cm2 Assembly code details F = with a rod frame H = for rod frame Support materials code code other pieces PVDF PP PVDF PP inox GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnières, France www.galvatek.com - Tél. 01 30 93 07 57 Fax. 01 30 93 25 04 -...

Open the catalog to page 4

All Galvatek catalogs and technical brochures

  1. Rotkappe BC

    2 Pages

  2. BC and BC/L

    2 Pages

  3. ROTKAPPE ABS

    2 Pages

  4. control box

    2 Pages

  5. Rotkappe LC

    2 Pages