Flat heaters type F, for frost protection Rigid structure ideal for important powers With options Feet & Cable-gland these models are specifically adapted to keep liquid storage tanks from freezing, all sizes with or without double wall. Installation through the inspection trap (ø 500 mm minimum). Can be installed in a tank filled when support feet are ordered on each side of the heating part. Can be passed through the inspection trap without interfering with the tank. For a complete efficiency we recommend a cable-gland installed on the non heating part N - positioning hole ø 75 mm to be planned on the dome - and a PFA coated PT100 probe mounted on heater. Length H corresponds to the installation height of the cable-gland on the N part. To ensure a proper positioning and avoid any mechanical damage of the cable, please allow an extra 300 mm on the H length. The cable is rolled up according dimensions & shapes proposed and held with PVDF, PP or PFA strips which ensure the right distance between the rolls. To secure completely the heating part it is then mounted on a rigid rod structure in PVDF or PP or on a stainless steel structure. Electric safety : the Galvatherm heater complies with protection class 1 of EN 60519-1/2. The cable is screened throughout the entire length by a copper earthing strip. The earthing must be connected to the earth. In order to provide maximum safety, a fault-current (FI) protection device (30mA) should be used.. Options and Accessories Extra length of cables Electrical connecting cable C of type H05 VV-F (PVC) or H07 RN-F (Neopren) Non heating cable N to go out of the tank The Galvatherm heater is only planned to heat liquids. Removable guard Perforated plastic guard PP ou PVDF Ref in PP : PRPPP Ref in PVDF : PRPPF Cable-gland Ø75 mm Feet (standard 100 mm) PP, PVDF or stainless steel for installation at fthe bottom Ref in PP : PIPP4-100 Ref in PVDF : PIPF4-100 Ref in stainless steel : PIIN4-100 (additional ballast possible) Allow between 200 to 300 mm extra on the H length (H=installation height on N) Ref in PP : PEPP Ref in PVDF : PEPF Probe mounted on heater PFA coated PT100 probe 2,3 or 4 wires, installed at the factory. Closed tank : the probe goes through the same cablegland as the one of the heater. Fixed by PP or Tefzel clamps Ref : contact us GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnières, France www.galvatek.com - Tél. 01 30 93 07 57 - info@galvatek

The table below informs on the dimensions of the heating part and its references. The reference number begins by P30, P40 or P90. These codes indicate the thickness 's device. P30 = thickness 30 mm / P40 = 40 mm / P90 = 100 mm All dimensions are given with a tolerance of ± 10 mm. Standard cable coating : PFA single layer. Double layer please contact us. GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnieres, France www.galvatek.com - Tel. 01 30 93 07 57 - [email protected]

THREE-PHASES IMMERSION HEATERS KW J x K 230V 3-ph 400V 3-ph KW J x K 230V 3-ph 400V 3-ph 1.5 kW For the construction of the reference, see following page. * If feet option : 6 feet required instead of 4 Other voltage available : GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnieres, France www.galvatek.com - Tel. 01 30 93 07 57 - [email protected]

Construction of the reference number P30 04 05 2 J P 0 0 code code N length C length assembly materials code code code code J = petit cote K = grand cote Cable code details Assembly code details F = with a rod frame H = for rod frame Support materials code code frame strips other pieces 1 = PVDF PVDF PVDF GALVATEK S.A.S - 9, rue de la Tour du Mesnil-Renard - 78270 Bonnieres, France www.galvatek.com - Tel. 01 30 93 07 57 - [email protected]