FUYU AUTOMATION FEC60 / FEC80 | Buyer-ready guide | Revision 2026.07 Position accuracy Turn application requirements into an order-ready cylinder, motor, drive, mounting, front attachment, control interface and accessory package. Chengdu FUYU Technology Co., Ltd. | [email protected] | +86-138-8070-2691

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK Choose electric actuation when the process needs programmable position, speed and thrust - without compressed-air infrastructure or hydraulic oil. TYPICAL TASKS Cell stacking, module pressing, fixture adjustment Clean actuation, programmable force/position and fast recipe changeover. FEC60 for compact stations; FEC80 for higher pressing force. TYPICAL TASKS Press-fitting, clamping, battery-pack assembly, test benches Flexible force/speed profiles, process data and easier model changeover. FEC80 is the preferred starting point for higher-force duties....

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK FAST SERIES CHOICE Source note: accuracy values above reproduce the supplied FUYU comparison table and are not universal limits for all competing products.

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK Complete these fields before selecting a part number or requesting a quotation. If side load, large moment, load rotation, impact, personnel lifting or a suspended vertical load is present, request an engineering review before ordering. • Peak force: the highest force during any segment, not only average payload weight. • Force at speed: use the exact force-speed point from the series table. • Equivalent duty: include acceleration, dwell, reversals and cycle frequency for thermal and life checks.

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK Features from the supplied FEC80 engineering brief; verify final configuration on the quotation. Design element IP65 IP65 does not mean submersible. Cable glands, mating connectors, motor/drive placement and installation workmanship must preserve the enclosure rating. www.fuyumotion.com | 5

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK Start with the required operating point, then choose geometry and control. Common package starting points Package ORDER RULE A complete order normally includes the cylinder, motor, servo drive, motor/encoder cables, mounting, front attachment, sensors and any required brake or regenerative resistor. www.fuyumotion.com | 6

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK FUYU 750 W servo without reducer Your required stroke is no more than 600 mm, force is within the corresponding table, and the smaller 65 x 75 mm body or lower system mass is valuable. External resistor means a regenerative resistor connected to the compatible servo drive. It is not an in-line mechanical component of the cylinder.

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK FUYU 1000 W servo without reducer *The current supplied catalog shows -15 to +60°C for FEC80. Confirm derating and validation near temperature limits in the formal quotation. You need more than 4 kN, stroke above 600 mm, higher structural capacity, or the FEC80 force-speed table is the first table that covers your complete duty. www.fuyumotion.com | 8

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK 7. Motor layout and 10 mounting combinations Choose the motor envelope first, then the mounting method compatible with that layout. Inline / direct motor - BC Narrow width, longer total length. Good when axial space is available. Parallel / folded motor - BL Shorter axial envelope, wider installation. Good when rear space is limited. Parallel / folded motor mounting choices Inline / direct motor mounting choices Rigid flange/base mounts require precise alignment. Pivoting mounts should use a compatible Y-clevis or spherical rod end so the rod is...

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK 8. Front attachment selection The attachment transmits force to the machine. Choose it from load geometry, joint freedom and maintenance needs. Direct threaded connection to a female machine feature Accepts a male stud or customer tooling Pin joint for one-axis articulation Allows angular misalignment around the joint Compact rigid connection; protect against misalignment Easy custom tooling interface Best with hinge or pivot mounts Reduces binding in pivoting mechanisms Rigid, accurately aligned machine: A or B threaded end. One-axis hinge motion:...

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK Motor technology and communication interface answer different questions. Use pulse/direction for simple positioning, RS485 Modbus for register-based PLC/HMI control, and CANopen/EtherCAT for higher-performance networked motion. Confirm the exact drive model before designing wiring. www.fuyumotion.com | 11

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK Request one quoted BOM with manufacturer part numbers, quantities, cable lengths and compatibility notes. This prevents a correct cylinder from arriving without the parts needed to run it. www.fuyumotion.com | 12

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK Use this architecture to define the system. Use the selected drive manual for actual terminals and pin numbers. Signals to agree before shipment Signal group A qualified controls engineer must complete terminal-level wiring, protective earthing, overcurrent protection, E-stop and vertical-load safety. Do not rely on software limits as the only safety layer. www.fuyumotion.com | 14

FUYU ELECTRIC CYLINDER | SELF-SELECTION HANDBOOK The final SKU must be generated or confirmed by FUYU because some combinations and motor options are non-standard. Typical configuration string Order examples • FEC60 compact high speed: FEC60, L10, E300, BC, FA, A, 750 W servo, no reducer. • FEC60 compact high force: FEC60, L10, E400, BL, L1, S, 750 W servo, R5. • FEC80 maximum force: FEC80, L10, E600, BL, L1, S, 1000 W servo, R10, brake and resistor as required. A configuration description is safer than typing an unverified long SKU. Ask FUYU to return the final order code, BOM, drawing and wiring...