COMPACT ELECTRIC FINGER Please read this MANUAL carefully before using the product.

EGB is a compact electric finger with high cost-performance and easy operation. It is equipped with an integrated servo controller for driving and control. It is compact in size, offers a wide range of force output, and has a fast opening and closing speed, exhibiting excellent motion performance. This compact electric finger can easily replace pneumatic grippers of the same specifications and is suitable for the rapid clamping and transportation of various lightweight products and components. This quick start guide provides comprehensive information on the product, including an overview, installation...

PRODUCT INFORMATION High-strength Wear-resistant Claw Head High Precision Steel Ball Guide Rail Mounting Holes on Multi-surface Signal Light Direct wiring out, connecting power and communication This MANUAL applies to the following product models * "1" is the side outlet, "2" is the bottom outlet.

PRODUCT INFORMATION This actuator is equipped with multiple mounting surfaces, allowing users to choose the appropriate mounting surface according to their specific needs and secure it with bolts that match the diameter of the holes. Please follow these guidelines when performing the installation and fixing operation: 1 ) When securing the main body, please use all the threaded holes on the same mounting surface for fixation; 2) When tightening the bolts, do not exceed the depth of the threaded holes. 1.3 Allowable Static Moment Direction of Finger MY

PRODUCT INFORMATION Clamp's clamping point distance: Please use the distance (L, H) from the mounting surface to the clamping point within the following range. Exceeding the limit range may cause excessive load torquebeing applied to the slider and internal mechanism of the gripper, potentially reducing its servicelife. • Even if the gripping point is within the restricted range, choosing smaller and lighter fixtures is advisable whenever possible. • When the clamp is too long, too large, or has excessive mass, the inertial force and bending load torque generated during the opening and closing...

PRODUCT INFORMATION * Requirements for use of outer support/drop detection SI+0.5mm < S2 Peripheral interfering objects

to the plug, you can cut off the plug end yourself. 2. Just follow the wire markings on the cables or the following wire sequence instructions to wire the cables accordingly. Loose wires that are not in use must be insulated to prevent short circuits caused by accidental contact of the wires. 2.3 Instructions of Signal Light Indicator I/O type is NPN

Cable Tying and Securing Protection for Installation 1. Recommendations for tying cable on device modules the gripper (the part simuwtnbe red) as static as possible with the gripper body to ensure effective fixation and prevent cable damage caused by bending/twisting below the minimum bendingradius (56mm). Note: Different batches of cables may cause slight differences in the color of the wire core. Please refer to the actual color of the cable for details.

1. When both the PLC and EGB feature NPN I/O types, the wiring method is as follows: PLC EGB(NPN) 2When both the PLC and EGB feature PNP I/O types, the wiring method is as follows:

3. When the PLC I/O type is PNP, while the EGB I/O type is NPN, indirect control can be achieved by using a relay wiring method, as follows: It is also possible to use a PNP to NPN converter or an NPN to PNP converter (as shown in the following figure) to achieve a high-to-low or low-to-high level conversion. Note: The PNP to NPN converter, or NPN to PNP converter, should be wired strictly following the wiring method provided by the cable manufacturer.

I/O INPUT AND OUTPUT SIGNAL DESCRIPTION The EGB supports I/O control with 3 inputs and 3 outputs. The product has preset multiple output levels and stroke, which can be achieved through the combination of I/O triggers, eliminating the need to connect external devices for parameter adjustment.

1. Before the initial use, please confirm whether the interval from the date of receipt to the first use exceeds half a month (reduce appropriately in winter). If it does, it is recommended to apply a small amount of WD-40 rust-preventing lubricant to the actuator's screw rod, guide rail, and other transmission components before use, and move back and forth 3-5 times to allow the lubricant to fully contact the transmission components, ensuring the actuator is in optimal condition. 2. If the actuator has not been used for more than half a month / has been left unused for an extended period: It...

The guiding components such as the guide fingers in this type of product are typically exposed to the air, and during the regular maintenance cycle, these parts may accumulate dust or other dark-colored impurities. To maintain the performance of the product and extend its service life, it is recommended to regularly clean and lubricate the product itself as well as its surrounding environment. When severe dirt is present on the product's surface or after a certain period of use, the following steps should be taken for cleaning, and the specific cleaning frequency should be determined based on...

(D Remove Excess Grease After applying the grease, the product will generally be in the condition shown in Figure 5; To maintain the overall aesthetic of the equipment, it is recommended to wipe off the excess grease with a clean cloth; © Anti-Rust Treatment for Guide Fingers The anti-rust capability of guide fingers is related to the presence of an oil film on their surface. Therefore, when wiping off the excess lubricating grease, you can wipe the entire surface once to ensure that a layer of oil film adheres to the surface, as shown in Figure 6. • It is recommended to manually open and close...

PRODUCT DISCLAIMER STATEMENT Dear Customer, First and foremost, we extend our heartfelt gratitude for choosing products from Chengdu FUYU Technology Co., Ltd. (hereinafter referred to as "we" or "our company"). This disclaimer aims to clarify the potential risks and responsibilities associated with the use of our products, ensuring that the rights and interests of both parties are effectively protected. Please read the following carefully and thoroughly understand the content. 1. Product Usage Risk Warning Our products are designed and manufactured in strict accordance with industry standards....