novatec ® HPN
1Pages

novatec® HPN - Engineered graphite with Kevlar® Material data Binders NBR Approvals WRC Colour black Surface both sides A310 black, with branding, optional with PTFE Sheet sizes and thickness tolerance Thickness: ± 7 % Physical properties Standard Unity Value * Gasket thickness 1.5 mm Identification DIN 28 091-2 Density DIN 28 090-2 Tensile strength FA – A1 - O [g/cm3] 1.50 DIN 52 910 longitudinal [N/mm2] 9 transverse [N/mm2] 7.5 175 °C, 16h, 50 N/mm2, [N/mm2] 38 175 °C, 16 h, 25 N/mm2, [N/mm2] 15 Residual stress σ dE/16 novatec® HPN, the tried and tested combination of graphite and Kevlar®, guarantee its extraordinary resistance to temperature and media together with its low percentage of NBR binder and its high density. The gasket’s good adaptability to flange irregularities as well as its excellent features in cutting and handling are further excellent properties of novatec® HPN. Compressibility ASTM F 36 J [%] 15 Recovery ASTM F 36 J [%] 30 Fluid resistance ASTM F 146 ASTM IRM 903 5h / 150 °C Weight change [%] 20 Thickness increase [%] 7 Weight change [%] 18 Thickness increase [%] 6 ASTM Fuel B water / steam 80 pressure (bar) 5h / 23 °C 5h / 100 °C [%] 20 Weight change 35 0 30 0 25 0 20 0 15 0 temperature (°C) [%] 25 Thickness increase 0 10 0 32 0 28 0 temperature (°C) 24 0 20 0 16 0 80 12 0 40 0 Coolant/Water (50:50) 40 0 20 60 50 40 -1 00 60 0 aqueous solutions 100 saturated steam curve 80 -5 0 pressure (bar) 100 DIN 52 913 All previous versions of this prospectus cease to apply. Subject to technical amendment. General data [%] 6 * = Mode (typical value) alkalis Applications 60 50 pressure (bar) pressure (bar) acids 35 30 25 20 15 10 5 0 -100 -50 temperature (° 150 200 250 300 0 50 100 C) 40 30 20 10 0 -100 -50 0 50 100 150 200 250 300 temperature (° C) • • • pipeline construction plant construction apparatus construction With the variety of installation and service conditions as well as of application and process engineering, the data of this sheet can only be taken as a non-binding guide. Product data temperature (° C) The 35 0 30 0 25 0 20 0 15 0 10 0 50 application recommendation for temperature and pressure in the diagrams mm and even flanges. Peak-to-valley 50 10 0 15 0 20 0 25 0 30 0 35 0 40 0 0 height 40 - 160 µm. -5 0 -1 temperature (° C) are applicable for a gasket thickness of 1.5 150 100 50 0 00 pressure (bar) gases 0 -5 0 0 20 0 temperature (° C) When using a gasket less than 1.5 mm thick the pressure and temperature limits may be higher. Kevlar® is a trademark registered by DuPont. In Sheets • Dimensions in mm: 2000 x 1000 • Thicknesses in mm: 1.2/1.5/2.0/3.0 In Rolls • Rolls: 1000 or 2000 mm • Thicknesses in mm: 0.5 to 1.0 mm Further dimensions and thicknesses available on request Quality Management ISO 9001, ISO/TS 16949 Environmental Managment ISO 14001 GASKETS TECHNICAL TEXTILES EXPANSION JOINTS INSULATION NEW MATERIALS Frenzelit Werke GmbH P.O. Box 11 40 · 95456 Bad Berneck · Germany Phone: +49 9273 72-0 ⋅ Fax: +49 9273 72-221 info@frenzelit.de · www.frenzelit.com FZ/5/08.10/001/FZ 60 40 -1 0 35 0 30 0 25 0 20 0 15 0 10 0 50 0 -5 0 pressure (bar) solvents 100 80 60 40 20 0 -1 00 pressure (bar) oils / refrigerants