Rapid level
18Pages

Patented level switches with unique characteristics.

RAPID LEVEL PATENTED LEVEL SWITCHES WITH UNIQUE CHARACTERISTICS * The required length can be obtained simply by cutting the steel rod, using an ordinary pipe cutter; or the switching point can be varied by using a float with through hole allowing the required liquid control point to be modified whenever necessary. * It can be used for dirty liquids, water, petroleum, cutting oils, and tolerates the presence of metal and ferrous particles, since the float does not hold a magnet and is integral with the rod. * One float can operate just one Reed (min. or max. level), or two Reeds (min....

Rapid Level connection rod cutting table. (NB: Carry out the cutting measurement with the rod in traction with respect to the body) F.lli Giacomello s.n.c. CONTROL VALUE L= (mm) L-L1 = 100 mm A-B = 90 mm H = 35 (L = 90 mm) H = 45 (L= 100 mm) H = 55 (L= 110 mm) H = 60(L= 120-500 mm) H = 90 (L = 501 -1000 mm) HI = 35 (LI = 90) HI =45 (LI =100) HI =70 (LI =120-1000 mm)

RAPID LEVEL"TYPE LEVEL SWITCH WITH 1 FLOAT RL/G1-TGAS ADVANTAGES OF THE RANGE 1- These electromagnetic level gauges in Kits can be obtained in the required length "L" simply by cutting the control rod with an ordinary pipe cutter and press fitting the float in the cutting place (see table for cutting). 2- The control rod can commutate the signal of 1 or 2 Reeds in sequence (with single or exchange contact). 3-The float does not hold magnets, therefore the Level can also be used in the presence of dirty liquids or ferrous particles. CONNECTION: FIXING DIAGRAM Connector CE

RAPID LEVEL"TYPE LEVEL SWITCH WITH 2 FLOATS * The RL/G2 range has a head which holds two control rods and two floats. * Each control rod can commutate the signal of 1 or 2 Reeds (with single or exchange contact). Each head can therefore contain from 2 to 4 Reeds. * The most suitable system can chosen for each rod. * In case of excessively dense liquids the two floats can be supplied entirely separate from each other to prevent rod 1 from undergoing friction with the float of rod 2. * The minimum distance between the two points to be controlled is 90mm. ELECTRICAL CONTACTS EXCHANGE REED SI =...

RL/G1 -L "RAPID LEVEL"TYPE LEVEL SWITCH FOR SIDE USE *This level switch for"side"use is very versatile: like the "RL" range, it can also be used to control the maximum or minimum level and for controlling the minimum plus empty or maximum or overflow. * Unlike the "RL" range, the distance between the 1st and 2nd signal is not fixed, but has an angular value, which gradually increases with the length of the rod. *This gives the designer many choices; in fact, by varying the length "L", the switching points of the 1 st and 2st Reed vary (read on axis 1 and 2). *The Level (see diagram S3) can...

LEVEL INDICATOR IN AISI316 WITH 1 OR 2 POINTS OF CONTROL AND TEMPERATURE UP TO 200 °C FEATURES: The Rapid Level series "AT" can be used in all situations where it is necessary to have parts in contact with the liquid completely in AISI 316. You can control up to 2 separate point of control. OPERATION: When the float rises or falls, the magnet in the upper part of the rod goes to activate or deactivate in the body 1 or 2 reed contacts, thus having the possibility of sending an electrical signal that can drive any device connected to it. ADVANTAGES: - Can be used with dirty liquid - Control...

PROCESS CONNECTION AND NUMBER OF CONTROL POINTS ELECTRICAL CONTACTS OF MINIMUM ROD "L" ELECTRICAL CONNECTION ELECTRICAL CONTACT OF MAXIMUM ROD "LI" ELECTRICAL CONNECTION ACTION POINTS S/STEEL STILLING OPERATING TEMPERATURE ELECTRICAL CONNECTION SPST - CLOSED IN THE ABSENCE OF LIQUID SPST - CLOSED IN PRESENCE OF LIQUID SPST - CLOSED IN PRESENCE OF LIQUID SPST - CLOSED IN THE ABSENCE OF LIQUID SPDT- EXCHANGE 1-5-2 1= COMMON 5= CLOSED IN PRESENCE 2= CLOSED IN ABSENCE SPDT- EXCHANGE 3-6-4 3= COMMON 6= CLOSED IN PRESENCE 4= CLOSED IN ABSENCE

MG - Mini Genius ENTIRELY IN PLASTIC MATERIAL FOR SMALL CONTROL UNITS * EASY TO USE there are two scales (oil and water) on the rod, that indicate the exact cutting place for obtaining the required switching point. * SAFE a) the level switch has structural separation of the electrical part from the tank; b) insensitive to dirty liquids and metal particles. * VERSATILE a) it can have two types of fixing (flange + thread) at the same time; b) the electrical contacts are reversible (N.O. / N.C. in pres.). * COMPATIBLE all parts of the level switch are made from the same material (nylon-glass...

Cutting the control rod. After choosing the scale corresponding to the liquid used (water - oil), cut the control rod with nippers or scissors at the place corresponding to the control level (see level "L"); then join the float to the rod, fitting it in the special seat.

A main feature of the MG range is reversibility: by shifting the position of the magnet (M) it is possible to have the contact CLOSED IN PRESENCE or CLOSED IN ABSENCE of liquid. Everything is made even easier by the presence of a label above the body, which makes positioning of the magnet inside the body clear and immediate. Except for particular cases, it is no longer necessary to order an SPDT exchange contact. MG - Mini Genius The level switch has the electrical part completely separate from the liquid and perfectly protected on the connector side. The result is a safer...

SUMMARY CHART MODEL li5 co 5 ■ > •z iu > Q o 0£ uj z LU X HI I CO CO H z m H 3 z O U- — z CO o LU -i OPERATING TEMPERATURE ELECTRICAL CONTACTS FLANGE 3 HOLES FLANGE 6 HOLES CONNECTION: Connector CE EN 175301-803-A IP65 PG.9/11

VISUAL IMMERSION LEVEL SWITCH FLANGED CONNECTION VISUAL MONITORING OF LIQUID LEVEL FIXING FLANGE 3 HOLES ROD PROTECTION AND CENTRING TUBE QUICK AND EASY ADJUSTMENT OF MINIMUM MONITORING POINT, LIKE FOR THE ENTIRE "RL" RANGE

RL/G1-V-T1/4 VISUAL IMMERSION LEVEL SWITCH 1"1/4 GAS THREAD CONNECTION AND NPT The easiest way to visually monitor the liquid level, without having to drill the side of the tank. Adjustment is quick and practical: - remove the float that creates a pressure seal with a silicone sheath (version with NBR float) - cut the rod and centring tube with a pipe cutter - refit the float - or it can be ordered already to size. The float pushes the rod, with an indicator at the top which clearly and accurately shows the level of the liquid. S/STEEL FLOAT DRILLING DIAGRAM SWITCHING POINT THE RING NUT...