PRODUCT CATALOG MOTORS & CONTROLS

For the most up-to-date product information, visit franklinwater.com.

4" SUBMERSIBLE MOTORS These motors are built for dependable operation in 4" diameter or larger water wells. BASIC FEATURES ■ Corrosion-resistant stainless steel exterior ■ Stainless steel splined shaft ■ Hermetically-sealed windings ■ StatorShield™ resin system ■ Filter check valve ■ Water lubrication ■ Kingsbury-type thrust bearing ■ Pressure-equalizing diaphragm ■ Built-in lightning arrestors (all single-phase; 200 & 300 V three-phase) ■ Removable Water-Bloc™ lead ■ Franklin-manufactured control boxes available for single-phase motors ■ UL 778 recognized (North American voltages) ■ CSA certified ■...

Franklin Electric

NOTE: Pack Designation (--S)=Single Pack, available in any quantitr; All 3 hp motors are single-packed; Contact factory for lead time for non-stocked items; Pallet packs available but not shown; Contact customer service for availability

Franklin Electric NOTE: Pack Designation (--S)=Single Pack, available in any quantitr; All 3 hp motors are single-packed; Contact factory for lead time for non-stocked items; Pallet packs available but not shown; Contact customer service for availability

Franklin Electric

NOTE: Pack Designation (--S)=Single Pack, available in any quantitr; All 3 hp motors are single-packed; Contact factory for lead time for non-stocked items; Pallet packs available but not shown; Contact customer service for availability

Franklin Electric 4" SUBMERSIBLE MOTORS - DIMENSIONS AND WEIGHTSSUPER STAINLESS NOTE: All dimensions listed above are for models supplied with lead; consult factory for other models NOTE: Consult factory for Coalbed Methane and 316 SS weights and dimensions

4" SUBMERSIBLE MOTORS - LEADS AND ACCESSORIESMOTOR LEADS AND CABLES BLACK OUTER BUSHING SLEEVE BLACK YELLOW RED NOTE: Refer to Franklin Application Installation Maintenance (AIM) Manual for accurate cable sizing; MOTOR WARRANT/ IS VOID if Fianklin-supplied leads are not used * Nitrile not for use in potable water

Franklin Electric 6" SUBMERSIBLE MOTORS These motors are built for dependable operation in 6" diameter or larger water wells. ■ Double flanged NEMA mounting design ■ Stainless steel splined shaft ■ StatorShield™, Franklin’s six-feature encapsulation system ■ High-capacity, Kingsbury-type, water-lubricated thrust bearing ■ Factory-filled with Franklin’s non-toxic water soluble fill solution ■ Field replaceable lead using Franklin’s exclusive Water-Bloc™ technology ■ Full 3,450 rpm 60 Hz design point ■ External sand slinger on shaft ■ Mechanical face seal at shaft exit ■ Copper bar rotor ■ All...

6" SUBMERSIBLE MOTORS - SPECIFICATIONS AND MATERIALS MOTOR SPECIFICATIONS Hz Sand Fighter® High-Temp 90° C** Sand Fighter® High-Temp 90° C** Duty Rating *At 0.5 ft/sec flow past motor, motors are rated for continuous duty up to 86°F (30 °C) water temperature. *At 0.5 ft/sec flow past motor, motors are rated for continuous duty up to 195°F (90 °C) water temperature and up to 86 °F (30 °C) water temperature with NO FLOW in lakes or in wells 12 inches or larger in diameter. CONSTRUCTION MATERIALS Component Construction Type Sand Fighter® UL Insulation Class Rating Class F Class F Motor Ambient Temp....

Franklin Electric

Franklin Electric

Franklin Electric NOTE: Models designated above as Sand Fighter® are water well construction; all 316 SS and Ni-Resist models are equipped with Sand Fighter® sealing system; all models listed above include factory-installed leads (13 ft)

6" SUBMERSIBLE MOTORS - DIMENSIONS AND WEIGHTSSTANDARD Standard Water Well NOTE: 6-Lead Y-A models available (add5 lbs to shipping weight) NOTE: 6-Lead Y-A models available (add5 lbs to shipping weight) 316 Stainless 0.94" MIN. FULL — SPLINE | 15 TOOTH 16/32 DIAMETRAL PITCH

Franklin Electric

8" SUBMERSIBLE MOTORS These motors are built for dependable operation in vertical 8" diameter or larger water wells. ■ Double flanged NEMA mounting design ■ Stainless steel splined shaft ■ StatorShield™ six feature encapsulation system ■ High-capacity, Kingsbury-type, water lubricated thrust bearing ■ Factory filled with Franklin’s non-toxic water soluble fill solution ■ Field replaceable lead using Franklin’s exclusive Water-Bloc™ technology ■ Full 3,525 rpm 60 Hz design point ■ External sand slinger on shaft ■ Mechanical face seal at shaft exit ■ Copper bar rotor ■ All models are variable frequency...

Franklin Electric NOTE: Specifications subject to change without notice; Contact Franklin Electric if current material types are required for bid specifications

Franklin Electric

Franklin Electric NOTE: Models designated above as Sand Fighter® are water well construction; all 316 SS models are equipped with Sand Fighter® sealing system; all models listed above include factory installed leads (13 ft); motor leads do not include ground

8" SUBMERSIBLE MOTORS - DIMENSIONS AND WEIGHTSSTANDARD Type 1.0 (40-150 hp) NOTE: 6-Lead Y-A models available (add5 lbs to shipping weight)

Franklin Electric

CONTROLS - control boxes The Quick Disconnect (QD) and Capacitor Run Control (CRC) control boxes are designed for use with Franklin 3-wire, single-phase submersible motors through 1 hp. The Standard and Deluxe control boxes are designed for use with Franklin 3-wire, single-phase submersible motors from 1 through 15 hp, and are recommended for water systems that use pressure switches, level switches, or other pilot devices. Deluxe boxes contain magnetic line contractors carefully matched to the motor rating, eliminating the need for external line connectors. FEATURES: ALL ■ Suitable for outdoor...

Franklin Electric NOTE: Q = Quick Disconnect Control Box; CRC=Capacitor Run Control Box; S=Standard Control Box; D=Deluxe Control Box; D-XL=Extra Large Deluxe Control Box