PROCESSING INSTRUCTIONS DETAILS AND CONNECTIONS / ADHESIVE STRENGTH TEST

Content GENERAL PROCESSING Cleaning and priming Preparation - Waterproofing Fleece cuts Adhesive strength test These processing instructions are designed for trained specialist companies and represent an overview of important training topics that can be looked up again here before processing. In addition, it provides instructions on how to carry out our adhesive strength test set. This means the following pages are no substitute for our training in waterproofing. Would you like to take a training course? These are available at our factory in Gollhofen or directly on site. Our Sales Representative...

Tools and aids for processing Nylon skin roller + roller handles 12 cm All-purpose fabric adhesive tape Professional scissors Cleaning cloth Spreading trowel + notched trowel blade Tip for surface waterproofing: Use 3.5 mm notched trowel blade Wood stirrer Disposable gloves Basket agitator Safety goggles Personal protective equipment (PPE) Safety goggles Long-sleeved clothing Oily skin protection cream

The system concept Our product brands FRANKOSIL®, REVOPUR® and FRANKOLON® refer to our three system solutions, each designed for special demands and requirements. Our FRANKOTHEK also includes and offers all products that are required for preparing and safely carrying out waterproofing work. FRANKO SIL® listed here are matched to our FRANKOSIL® system The convenient 1-component waterproofing system for connections and details in roof and structural • Particularly easy to process The tools, primers, fleeces and additional products • Free of hazardous substances and non-toxic • Fastest variant in...

PR110 (FPO PRIMER) Can be reworked after Material consumption colour shade PR115 (MULTI-PLASTIC PRIMER) Can be reworked after approx. 60 mins1 Material consumption approx. 80-100 ml/m2 colour shade yellowish PR130 (SL BONDING AGENT) Can be reworked after approx. 15 mins1 Material consumption approx. 100 ml/m2 Colour shade colourless (FILLER AND MODELLING COMPOUND) processing time approx. 20 mins1 Can be reworked / walked on after approx. 1 h1 Material consumption according to application Colour shade 7047 (telegrey 4) TH610 (V600) Material consumption according to application Colour shade colourless...

FRANKO THEK Substrate preparation Free from dirt, oils or greases as well as other coatings and loose components. The area to be sealed Standing water, ice and must have sufficient snow on the substrate material strength. are not permitted for sealing work. Only cover an area that can be recoated in the same working day. If this is not done, the primer must be removed by sanding or by cleaning with TH610 (V600). Do not pour the primer directly onto the surface to be sealed. Do not use the same cloth for the primer that was previously used to apply the cleaner. Cleaning & priming TIP: We recommend...

PR115 (multi-plastic primer) SYSTEM REVO PUR® 1. Clean the substrate with TH610 (V600) (with a clean cloth!) until no residue is visible on the cleaning cloth. FRANKO LON® 2. Pour PR110 (FPO Primer) into a clean container. 1. Clean the substrate with TH610 (V600) (with a clean cloth!) until no residue is visible on the cleaning cloth. 2. Add hardener component B completely to the base component. 3. Close the aluminium bottle well and shake well for approx. 30 seconds. 4. Use a brush to apply PR115 (multi-plastic primer) to the prepared surface with approx. 80-100 ml/m². PRACTICAL TIP In the absence...

1. Clean the substrate TH610 (V600) (and a clean cloth!) until no residue is visible on the cleaning cloth. 2. Then roughen the cleaned substrate with sandpaper or sanding disc (e.g. ZEC disc - grit P40-60). FRANKOSIL SPEEDFIX 2 kg combination plastic container 1. Knead the bags of component A and component B thoroughly for approx. 30 seconds before opening. 2. Empty component A FRANKOSIL® 1K PLUS completely into the outer packaging bucket. 3. Add all of component B FRANKOSIL® SPEEDFIX filler. 4. Mix homogeneously and without any lumps using a mixing paddle. 5. Apply the filler and modelling...

FRANKO SIL®

Waterproofing FRANKOSIL® 1K Plus 1. Measure the area to be sealed and cut the fleece accordingly. Always allow for an overlap of 5 cm for individual fleece cuts. 2. Apply adhesive tape approx. 5 mm above the outer edge of the fleece cut. 3. FRANKOSIL® 1K Plus is stirred evenly with a wood stirrer or basket agitator. Always apply the adhesive tape to a cleaned surface (see p. 12). FRANKOSIL® 1K Plus is too thick in cool weather? The areas to be sealed must always be carefully taped without gaps. The liquid plastic can generally be diluted with up to max. 3% by volume (corresponds to approx. 90...

FRANKOSIL® Turbo Shot Applying the 1st layer 4. FRANKOSIL® Turbo Shot 5. Stir FRANKOSIL® 1K Plus must be shaken thorough- evenly with a wood stirrer or ly. Then empty the amount basket agitator. of FRANKOSIL® Turbo Shot table and stir it evenly into the The FRANKOSIL® Turbo Shot not only accelerates the curing of FRANKOSIL® IK Plus to approx. 90 mins, but also reduces the processing time to max. 15 mins. For the correct measurement of FRANKOSIL® Turbo Shots, simply use the measuring cup provided: Mixing ratio Inlaying the polyester fleece The fleece is inlayed into the still fresh sealing of...

SEALED SUCCESSFULLY? The following properties show whether sufficient material has been used immediately after the sealing work: 1. Glossy surface 2. Slight surface structure visible If the surface is matt, this means too little material has been applied. Apply the 2nd layer either with a brush... or with spreading trowel After inlaying the fleece into the still fresh 1st layer, apply the rest of the specified quantity, 1/2 to 1/3 of FRANKOSIL® 1K Plus, to the surface. Remove the adhesive tapes immediately afterwards. PRACTICAL TIP No stress with FRANKOSIL® 1K Plus: The 1st and 2nd layer can...