EXCERPT FROM 1.2 DETAILED SERIES INFORMATION PROLINK ENGINEERING MANUAL 01/24 (Ref-No. 888) siegling prolink modular belts SERIES 6.1 Straight running belts Pitch 50 mm (1.97 in) Forbo Siegling GmbH Lilienthalstraße 6/8, D-30179 Hannover Phone +49 511 6704 0 www.forbo-siegling.com, [email protected] Siegling Prolink Engineering Manual · 01/2024

siegling prolink modular belts Straight running belts | Pitch 50 mm (1.97 in) Belts for medium to heavy-duty, hygiene-critical applications Side view scale 1:1 Available surface pattern and opening area S6.1-0 FLT Closed, smooth surface S6.1-0 NTP Closed surface and round studs Design characteristics – Wide modules and eyelets for less soiling S6.1-0 CTP Closed surface and pointed studs – Hinges that open wide, wide channels on the underside and a continuous drive bar for an easy-to-clean design S6.1-21 FLT Open (21 %), smooth surface – Robust design and smooth, cut-resistant surface (depending...

BELT TYPESsiegling prolink modular belts Straight running belt | Pitch 50 mm (1.97 in) Closed, smooth surface | Flat top surface | Easy-to-clean Belt dimensions Available standard materials 3> Belt Mold to order belts Mold to width available in: 100 mm (3.94 in), 140 mm (5.51 in), 200 mm (7.87 in), 220 mm (8.66 in), 400 mm (15.75 in) * Values valid for dry applications (RH <50 %o). Belts in PA material will absorb water in wet environments, causing them to expand and reduce the nominal belt pull capacity. ■ BL (Blue), ■ LB (Light blue), UC (Uncolored), WT (White) All measurements and tolerances...

BELT TYPESsiegling prolink modular belts Straight running belt | Pitch 50 mm (1.97 in) S6.1-0 NTP | 0 % Opening | Nub top (round studs) Closed surface and round studs | 6 % contact area | Nub top surface for good release of wet and sticky products | Easy-to-clean Belt dimensions Available standard materials 3> Belt Mold to order belts OOOQOOQOOQOOQC □ ooooooooooooo OOOOOOQOOQOOQC 0 00000000000"“ Mold to width available in: 100 mm (3.94 in), 200 mm (7.87 in), 400 mm (15.75 in) OQOOOQOOOO/ 30000000000 OQOOOOOOOO/ “OOOOOOO OJ Also available with molded indent 40 mm (1.57 in) ■ LB (Light blue), WT...

BELT TYPESsiegling prolink modular belts Straight running belt | Pitch 50 mm (1.97 in) S6.1-0 CTP | 0 % Opening | Cone top (pointed studs) Closed surface and pointed studs | Cone top surface pattern for superior grip | Easy-to-clean Belt dimensions Available standard materials 3> Belt Mold to order belts Mold to width available in: 400 mm (15.75 in) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 ‘Temperature influence". All imperial dimensions (inches) are rounded off. 11 Flex radii: r1 = side flex, r2 = front flex on roller, r3...

BELT TYPESsiegling prolink modular belts Straight running belt | Pitch 50 mm (1.97 in) S6.1-21 FLT | 21 % Opening | Flat top Open area (21 %) for excellent air circulation and drainage | 72 % contact area (Largest opening: 1.9 x 11 mm/0.07 x 0.43 in) | Smooth surface | Easy-to-clean Belt dimensions Available standard materials 3> Belt Mold to width available in: 100 mm (3.94 in), 200 mm (7.87 in) ■ LB (Light blue), UC (Uncolored), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 "Temperature influence". All imperial dimensions...

BELT TYPESsiegling prolink modular belts Straight running belt | Pitch 50 mm (1.97 in) S6.1-23 FLT | 23 % Opening | Flat top Open area (23 %) for excellent air circulation and drainage | 71 % contact area | Smooth surface | Easy-to-clean Belt dimensions Available standard materials 3> Belt Mold to order belts Mold to width available in: 100 mm (3.94 in), 200 mm (7.87 in), 400 mm (15.75 in) ■ BL (Blue), ■ LB (Light blue), UC (Uncolored), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 "Temperature influence". All imperial...

Straight running belt | Pitch 50 mm (1.97 in) Open area (36 %) for excellent air circulation and drainage | 35 % contact area (Largest opening: 11.8 x 14.4 mm/0.46 x 0.57 in) Smooth surface | Easy-to-clean p Mold to order belts Attention! Due to the very large surface openings, personnel must be instructed not to place their fingers in or on this belt. ■ BL (Blue), ■ LB (Light blue), UC (Uncolored), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 "Temperature influence". All imperial dimensions (inches) are rounded off....

siegling prolink modular belts SERIES 61 | SPROCKETS Straight running belt | Pitch 50 mm (1.97 in) Special easy-to-clean sprocket with enhanced tooth engagement for excellent force transmission Main dimensions Sprocket size (Number of teeth) Shaft bores (• = Round, ■ = Square) 30 mm All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 ‘Temperature influence". All imperial dimensions (inches) are rounded off. For detailed sprocket and shaft dimensions see appendix 6.3 Number of sprockets (sprocket spacing distance) see chapter 3.2

Straight running belt | Pitch 50 mm (1.97 in) siegling prolink modular belts S6.1-0 FLT PMU/S6.1-0 FLT PMU I40 Flat top surface for dry products Basic dataMaterial Color Height (h) • = no indent, ▲ = with indent 40 mm ■ BL (Blue), ■ LB (Light blue), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 ‘Temperature influence". All imperial dimensions (inches) are rounded off. Note: Use of accessory in a belt may impact on the minimum design radii. Please see chapter 6.3 for further information.

PROFILES siegling prolink modular belts Straight running belt | Pitch 50 mm (1.97 in) No cling surface with nub top base to improve release of wet and sticky products Basic data Material ■ LB (Light blue), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 ‘Temperature influence". All imperial dimensions (inches) are rounded off. Note: Use of accessory in a belt may impact on the minimum design radii. Please see chapter 6.3 for further information. MOVEMENT SYSTEMS