Series 11
9Pages

Catalog excerpts

EXCERPT FROM PROLINK ENGINEERING MANUAL 12/17 (Ref-No. 888) siegling prolink modular belts SERIES 11 Side flexing belts Pitch 25 mm (0.98 in) D Forbo Siegling GmbH Lilienthalstraße 6/8, D-30179 Hannover Phone +49 511 6704 0, Fax +49 511 6704 305 www.forbo-siegling.com, siegling@forbo.com Prolink Engineering Manual · 12/2017

Open the catalog to page 1

siegling prolink modular belts Side flexing belts l Pitch 25 mm (0.98 in) Belts for light-duty food and non-food applications Side view scale 1:1 Available surface pattern and opening area S11-45 GRT Open (45 %), lattice-shaped surface with replaceable caps Design characteristics – 45 % open area provides excellent cooling and draining capabilities – All plastic lightweight belts (plastic pins) – Tight radius belt with minimum curve radius of 1.4 x belt width – Outermost hinge is fixed to the pin to prevent deflection and elimination of potential belt edge catch points – Suitable for both...

Open the catalog to page 2

S11-45 GRT | 45 % Opening | Grid top Open area (45 %) for excellent air circulation and drainage | Lattice-shaped surface with robust, replaceable caps on the belt edges Variant specific dimensions [mm (in)] Belt dimensions dpin BL (Blue), UC (Uncolored), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 "Temperature influence". All imperial dimensions (inches) are rounded off. 11 Flex radii: r1 = side flex, r2 = front flex on roller, r3 = back flex on load bearing roller, r4 = back flex on Hold Down shoe, r5 = back...

Open the catalog to page 3

Side flexing belts l Pitch 25 mm (0.98 in) Open area (45 %) for excellent air circulation and drainage | Lattice-shaped surface with replaceable Hold Down caps Belt dimensions dpin BL (Blue), UC (Uncolored), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 "Temperature influence". All imperial dimensions (inches) are rounded off. 11 Flex radii: r1 = side flex, r2 = front flex on roller, r3 = back flex on load bearing roller, r4 = back flex on Hold Down shoe, r5 = back flex on roller 21 Complies with FDA 21 CFR 31...

Open the catalog to page 4

S11-33 FRT2 | 33 % Opening | Friction top (Design 2) Open area (33 %) for full FRT2 surface area) | Lattice-shaped surface with friction top, flat integrated friction pads in flat (FRT2) version for better grip. Minimum indent FRT2: 125 mm (5 in)/175 mm (7 in) Belt dimensions dpin BL (Blue), UC (Uncolored), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 "Temperature influence". All imperial dimensions (inches) are rounded off. 11 Flex radii: r1 = side flex, r2 = front flex on roller, r3 = back flex on load bearing...

Open the catalog to page 5

Side flexing belts l Pitch 25 mm (0.98 in) Main dimensions Shaft bores (• = Round, ■ = Square) inch inch inch inch Material: PA, Color: LG LG (Light gray) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 "Temperature influence". All imperial dimensions (inches) are rounded off.

Open the catalog to page 6

Side flexing belts l Pitch 25 mm (0.98 in) For side support and return roller without tooth engagement Main dimensions Spiocket size (Numbei of teeth) Shaft bores (• = Round, ■ = Square) 25 Material: PA, Color: LG I G 'I Mhl ■ ||.|y' All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 ‘Temperature influence". All imperial dimensions (inches) are rounded off.

Open the catalog to page 7

Side flexing belts l Pitch 25 mm (0.98 in) For retention of bulk products BL (Blue), ■ DB (Dark blue), UC (Uncolored), WT (White) All measurements and tolerances apply at 21 °C; for temperature deviations please see Prolink manual chapter 4.4 "Temperature influence". All imperial dimensions (inches) are rounded off. Note: Use of accessory in a belt may impact on the minimum design radii. Please see chapter 6.3 for further information.

Open the catalog to page 8

i Series S1 ... S14 a Open area/Sprocket size p- 'I' -lilag- ■ 'I ■■ 'M ii' '■ I Format: xx E.g. 20 = 20 % I oi spun kels: numbei of teeth I oimal: "/"xx E.g. /12 = 12 teeth s Height/Diameter/ Bore size and style Height in mm Format: Hxxx pin diam-l-i in mm I o'l mat Dxxx Bore size: SQ (= square) or RD (= round) either in mm ■ t in he -• Format: SQxxMM or RDxxIN 1 Length/Width Pins Length in mm I or map I /// M/'dul- e width in mm I mmaP W/// * For each series' standard colors please refer to the table of materials for each belt (chapter 1.2). A number of other colors are available on...

Open the catalog to page 9

Series 11 9Pages

Catalog excerpts

All Forbo Siegling GmbH catalogs and technical brochures

Series 11
9Pages