AC Antistatic Bar with Air SE-ACA Series
8Pages

{{requestButtons}}

Catalog excerpts

AC Antistatic Bar with Air SE-ACA Series - 1

www.fogegmbh.com info@fogegmbh.com FÖGE ELEKTRONIK GMBH Böhleswasenweg 11 72555 Metzingen +49 7123 9570508 Instruction Manual Product: SE-ACA Series AC Antistatic Bar with Air

Open the catalog to page 1
AC Antistatic Bar with Air SE-ACA Series - 2

IMPORTANT Attention: When assembling ionisers without air, always emitter direction should look towards the part. Tilt mounting up to 45 degrees would be ok but be informed that higher than this angle will effect ionisation in negative way. Emitter Emitter Direction Mounting bracket can be metal or any other material Mounting distance varies according to the antistatic product, check specifications Up to 45 degree angle is applicable, more than this tilting angle of the part effects negative on ionisation Attention: Do not cover the ioniser with metal or attach metal close to the emitter...

Open the catalog to page 2
AC Antistatic Bar with Air SE-ACA Series - 3

IMPORTANT Attention: When assembling ionisers with air, always air direction should look towards the part. Tilt mounting up to 45 degrees would be ok but be informed that higher than this angle will effect ionisation in negative way. Part to be neutralized Nozzle – emitter angle 45 – 90 degrees. Mounting bracket can be metal or any other material Mounting distance varies according to the antistatic product, check specifications Up to 45 degree angle is applicable, more than this tilting angle of the part effects negative on ionisation Attention: Do not cover the ioniser with metal or attach...

Open the catalog to page 3
AC Antistatic Bar with Air SE-ACA Series - 4

1. Intended Use SE-ACA Series Antistatic Bar with Air is designed for use in industrial areas. Purpose of the product is neutralizing and cleaning the charged plastic, glass, fabric or any parts which are not conductive. Airflow from the ionizer will carry negative and positive ions which will ionize the part and eliminate static electricity which causes quality and safety problems. The system must be operated within the limits specified in technical data and used according to technical specifications as well as installation instructions. The system must be used in such a way that no person...

Open the catalog to page 4
AC Antistatic Bar with Air SE-ACA Series - 5

3. Dimensions / Installation System operation assumes knowledge of the assembly instructions. The symbols used for safety is shown in section 8(Safety) of manual. Air Hose Diameter = 8mm SE-CAB-AC-1: Non standard option 1mt cable can be ordered up to 15mt. The total length of the equipment to be connected to the power unit should not exceed 15 meters. Power unit can supply totally 15 meters length of cable and bar.

Open the catalog to page 5
AC Antistatic Bar with Air SE-ACA Series - 6

4.Electrical Connection Additional Earth Connection (Recommended to connect separately) Fuse Cap F0.5AL250V Fast Blow Glass Fuse 5x20mm Connect Antistatic Bar with Metal Screw Type HV Connectors which FÖGE bars have as a connection. 5.2. Controls • ON/OFF Switch

Open the catalog to page 6
AC Antistatic Bar with Air SE-ACA Series - 7

6. Faults In any of below cases or others do not open the product. If switch is on but the ON/OFF light is OFF, change the fuse inside the power unit. Fuse type: F0.5AL250V Fast Blow Glass Fuse 5x20mm 7. Warnings Connect the power supply and the display/output device according to the safety regulations for electrical equipment. The supply voltage must not exceed the specified limits. Avoid shocks and impacts to the sensor. Protect the cable against damage. Possible Results of Avoidance Risk of injury by electric shock Damage to or destruction of the sensor 8. Maintanence Because of the...

Open the catalog to page 7
AC Antistatic Bar with Air SE-ACA Series - 8

9. Safety System operation assumes knowledge of the assembly instructions. The following symbols are used in these assembly instructions: Indicates a hazardous situation which, if not avoided, may result in minor or moderate injury. Indicates a situation that may result in property damage if not avoided. Indicates an electrical shock if not avoided or properly follow comments. 10.Liability for Material Defects All components of the device have been checked and tested for functionality at the production facility. However, if defects occur despite our careful quality control, FÖGE or your...

Open the catalog to page 8

All FÖGE Elektronik GmbH catalogs and technical brochures