FOCUS LCDsLCDs MADE SIMPLE® Ph. 480-503-4295 | [email protected] Part Number E43GB-I-MW800-CBOverview: • IPS, Transmissive • Capacitive Touch Panel • RoHS Compliant • Wide Temperature Range

This is a color active matrix TFT (Thin Film Transistor) LCD (Liquid Crystal Display) that uses amorphous silicon TFT as a switching device. This model is composed of a transmissive type TFT- LCD Panel, driver circuit, capacitive touch panel, and backlight unit. The resolution of the 4.3” TFT- LCD contains 480x800 pixels and can display up to 16.7M colors.

1. DISPLAY TYPE: 4.3" TFT-LCD 2. DISPLAY MODE: IPS, NORMALLY BLACK DO NOT SCALE OFF THIS DRAWING. All dimensions are given in good faith and believed to be correct. These drawings are for general presentation purposes only. No responsibility can be taken with any errors found by measuring off this drawing. The Focus LCDs PDF drawing should be referenced as the master file. THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF FOCUS DISPLAY SOLU TIONS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOU T THE WRITTEN PERMISSIONS OF FOCU S DISPLAY SOLUTIONS, INC. IS PROHIBITED FOCUS...

I: Input, O: Output, P: Power

ptical Specification eference Notes: (1) Definition of Viewing ngle: The viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the hori ontal or 3,9 o'clock direction and the vertical or 6,12 o'clock direction with respect to the optical axis which is normal to the LCD surface. Normal x - y - 00 yx - 900 (2) Definition of ontrast atio: Measured at the center point of panel. The contrast ratio (Cr) measured on a module, is the ratio between the luminance (Lw) in a full white area (R=G= =1) and the luminance (Ld) in a dark area (R=G= =0)....

(5) Definition of olor Gamut: Measuring machine CFT-01. NTSC’s Primaries: R(x,y, ), G(x,y, ), (x,y, ). FPM 20 of Westar Display Technologies, INC., which utili ed SR-3 for Chromaticity and M- A for other optical characteristics. The color chromaticity shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. Fig. 1931 CIE Chromacity Diagram Color Gamut: =gfArea of RG Triangledx 100% Area of NTSC Triangle (6) Definition of ptical Measurement Setup: The LCD module should be stabili ed at a given...

5.3 L ED Backlight Characteristics The backlight system is edge lighting type with 10 LED Chips Note 1: LED lifetime (Hr) can be defined as the time in which it continues to operate under the condition: Ta=25 ±3°C, typical IL value indicated in the above table until the brightness becomes less than 50%. Note 2: The “LED lifetime” is defined as the module brightness decrease to 50% original brightness at Ta=25° C and IF = 180mA. The LED lifetime could be decreased if operating IF is larger than 180mA. The constant current driving method is suggested. Note 3: Luminance U niformity of these 9 points...

haracteristics igh Speed Data Transmission: Data- lock Timing For high-speed data transmission data-clock timing diagrams and tables, see table and diagram on page 31 of the data sheet for controller ILI9806E. The data sheet can be found here: https://focuslcds.com/wp-content/uploads/Drivers/ILI9806E.pdf igh Speed Data Transmission For high speed data transmission diagrams and tables, see the first table and diagram page 64 of the data sheet for controller ILI9806E. The data sheet can be found here: https://focuslcds.com/wp-content/uploads/Drivers/ILI9806E.pdf Turnaround Procedure For turnaround...

For I2C timing diagrams and tables, see page 9 of the data sheet for touch panel IC GT911. The data sheet for GT911 can be found here: https://focuslcds.eom/content/G T911.pdf

For the power on timing diagram, see the first diagram on page 10 of the data sheet for touch panel IC GT911. The data sheet for GT911 can be found here: https://focuslcds.com/content/GT911.pdf For the host resetting timing diagram, see the second diagram on page 10 of the data sheet for touch panel IC GT911. The data sheet for GT911 can be found here: https://focuslcds.com/content/GT911.pdf Timing for Setting Slave ddress to 0x28/0x29 For this setting slave address timing diagram, see the third diagram on page 10 of the data sheet for touch panel IC GT911. The data sheet for GT911 can be found...

1. When the module is assembled, it should be attached to the system firmly. Do not warp or twist the module during assembly work. 2. Protect the module from physical shock or any force. In addition to damage, this may cause improper operation or damage to the module and back-light unit. 3. Note that polarizer is very fragile and could be easily damaged. Do not press or scratch the surface. 4. Do not allow drops of water or chemicals to remain on the display surface. If you have the droplets for a long time, staining and discoloration may occur. 5. If the surface of the polarizer is dirty, clean...