fluimac pump solution

pump solution Manual hand pumps are always a useful and cost effective alternative to conventional electric or air operated drum pumps when only small quantities of media have to be removed out of canisters or drums or if the customer would use the drum pump only occasionally or rarely. Depending on the medium different pump tube materials and gaskets are available. In principle the hand pump can be divided into three groups: for chemicals such as acids, alkalies and detergents for mineral oil products and for flammable liquids such as gasoline or solvents. The maximum viscosity of the pumped fluids...

pump solution Pump tubes made of polypropylene (PP) are suitable for neutral, aggressive and hardly combustible liquids. They are used specifically for pumping aggressive chemicals such as acids, alkalies or detergents. Drive shaft: Stainless steel 316 Ti or has-telloy 2,4610 Media temperature: max. 50 °C Media: Formic acid (50%), ammonia, boric acid, distilled water, liquid fertilizers, iron-II and III-chloride, acetic acid (80%), photo developers, fruit acids, potassium hydroxide, copper chloride, lactic acid, sodium hydroxide, phosphoric acid, hydrochloric acid, sulfuric acid (up to 90%),...

pump solution Hand pump N-02 Hand pump N-02 for acids, alkalies and water-based chemicals Pump material: Polypropylene Shaft: Stainless steel 316 Ti Seals: FKM Flow rate: 0,3, 0,37 or 0,45 l/stroke* depending on lever position The telescopic suction tube is adjustable from 340 to 900 mm and has a diameter of 40mm. The pump housing has two threads G2 "and G 1 %". Order No.: 6002 0000 Hand pump N-03 Hand pump N-03 for oils, diesel, alcohol up to max. 50%, antifreeze liquid, water, etc. Pump material: Polypropylene Shaft: Tool steel Seals: NBR Flow rate: 0,3, 0,37 or 0,45 l/stroke* depending on...

pump solution NEPTUNE Manual hand pumps Hand pump N-05 Stainless steel hand pump Pump tube made of stainless steel V4A (316 Ti), all gaskets made of PTFE. Therefore especially suitable for flammable liquids such as solvents (including acetone). Certified: risk analysis made by TUEV Suction tube lengths: 700 and 1,000 mm Flow rate: 0,3-0,6 l/stroke* Necessary accessories Order No.: Discharge arc with PTFE 6510 seal and wing nut Hose connection made of stainless steel, with PTFE seal and wing nut made of brass, nickel plated Hose connection %" 6520 Drum adapter made of brass 6540 nickel plated...

pump solution Hand pump N-08 Hand-crank rotary pump for chemicals The pump is suitable for thin fluid, highly aggressive media such as acids and alkalies. Hand pump N-09 Suitable for almost all highly liquid and slightly aggressive media such as acids, alkalis and chemicals. Better resistance as N-02 due PP-sheathed shaft. Material: Polypropylene Telescopic suction tube: 3 parts, polyethylene Seals: FKM Suction depth: for containers to 960 mm Pump material: PVDF Seals: PTFE Suction tube length: 3 x 35 cm Flow rate: 0,3 l/rotation* Pump complete with discharge arc and drum adapter G 2". Regular...

NEPTUNE Manual hand pumps Hand pump N-13 Metal hand crank rotary pump The pump is suitable for diesel, heating oil, oils (up to SAE 90) and all other self-lubricating, non-aggressive and non-flammable media. Pump material: pump housing made of cast iron Seals: NBR Flow rate: 0,25 l/rotation* Suction tube length: 980 mm; therefore suitable for smaller containers and 200 liter drums Pump complete with discharge arc and drum adapter G 2". For drums and containers from 30 to 200 liters. Hand lever pump made of metal The telescopic suction tube enables an universal use for all barrel sizes. For transferring...

pump solution Thread adapters Thread adapters Thread adapters made of PE for equalization of different threads at canisters, drums, containers, etc. when fixing f.e. hand pumps. All FLUIMAC hand pumps have a bung adapter (2" BSP male thread) that is suitable for metal drums like S 60 or S 200. Due to the big variety of different canisters, drums, containers, etc. that are available in the market there is often a need to use an adapter to fix the pump in the drum securely. Material of adapter: PE (Polyethylene) This plastic material is resistant to water, many alkalies, acids and salt solutions....

NEPTUNE Laboratory pumps Electric or air operated laboratory pumps with a suction tube made of polypropylene (0 25, 28 or 32 mm) or stainless steel 316 Ti (0 28 or 32 mm) The economic and safe solution for the filling and transferring of small quantities of neutral and aggressive media like acids and alkalies means FLUIMAC laboratory pumps. The particular advantages in an overview: • Designed for a safe and easy filling of low quantities out of narrow-necked containers and canisters. • Suitable for almost all thin fluid, neutral or corrosive media, but not for flammable liquids (for stainless...

Ofluimac pump solution N-120 NEPTUNE Electric universal motor N-140 230 Volt, 50 Hz, 250 or 450 Watt, IP 24, alternatively 115 Volt, 60 Hz Description • The drives N-120 and N-140 are compactly built, not explosion-proof, internally ventilated universal motors in various power classes. • The lightweight, handy and powerful devices can be used to drive the suction tubes of the laboratory pumps and drum pumps and are suitable in this combination for many thin liquid, neutral, aggressive and non-flammable media. Their sophisticated, technically clear structure ensures an efficient and safe use when transferring...

pump solution Electric universal motor 230 Volt, 50 Hz, 450 Watt, IP 24, double insulation protection class II, over load protection switch with or without low voltage release. Thermal protection, 5 m cable with plug. Also available in 115 volts, 60 Hz. Speed control as option. Operating data Flow rate (with hose and oval gear meter): 0 25 mm up to 23 l/min* 0 28 mm up to 40 l/min* 0 32 mm up to 49 l/min* Head: 0 25 mm up to 7 m* 0 28 mm up to 9 m* 0 32 mm up to 10 m* Viscosity: up to 400 mPas* Density: up to 1,3* LVR: Low voltage release SC: Speed control Q (l/min) N-140, 230 VAC, N-PP(HC)32,28,25-1,000,...