For additional information, contact us by email : contact@fluigent.com or consult our website : www.fluigent.com1 TABLE OF CONTENT RX - PRESSURE SOURCE USER MANUAL & DATASHEET
8Pages

RX - PRESSURE SOURCE USER MANUAL & DATASHEET VERSION 5 - JUNE 2020 TABLE OF CONTENT INTRODUCTION2 GENERAL DESCRIPTION GETTING STARTED AVAILABLE ACCESSORIES WARRANTY5 APPENDIX 1 For additional information, contact us by email : contact@fluigent.com or consult our website : www.fluigent.com

INTRODUCTION This document presents the general usage of the RX compressor – gas pump. It will cover the basic usage when associated with instruments, i.e. pressure controllers such as the Fluigent PX series or other end user or OEM instruments. The remote communication through the RS232 protocol and how to set custom pressures or reconfigure your product. GENERAL DESCRIPTION The RX is a pressure source packaged in powder coated steel enclosure. It can be used as a standalone equipment or be integrated in OEM system.s The RX can be mounted in any position or direction (horizontal or...

DATASHEET SPECIFICATIONS PNEUMATIC SPECIFICATIONS Minimum pressure Maximum pressure Free flow (flow rate at 0 mbar output) Flow rate at 2000 mbar ELECTRICAL SPECIFICATIONS Power voltage Maximum current Maximum power consumption PNEUMATIC SPECIFICATIONS Dimensions (L x W x H) *the RX has a built in drying component, it will reduce the humidity of the air supply to prevent condensation. This component is designed to perform in room temperature, for more detailed information on air supply conditions of your setup please contact us. LOCAL USAGE The RX can be used with any instrument needing a...

The table that follows will give you the standard usage of these positions with Fluigent products: LEFT POSITION Up to 4 PX 1 bar 1 or 2 Flow-EZ 1 bar (with or without a pressure tank) RIGHT POSITION 2 PX 2 bars for low volume reservoirs (performances will be degraded for higher volumes) 1 PX 2 bars for higher volumes 1 Flow-EZ 2 bars (better response time without an intermediate tank RS-232 INTERFACE The RS-232 interface is a 9-pin D-Sub socket used for remote communication. The voltage level is ±10 V (pin 5: GND; pin 2: RX +-10V; pin 3: TX +- 10V). For communications, use the following...

For all commands (no question mark “?”), the value is the required parameters to be sent to the instrument following the string in the command column. In case of error in the command spelling, the command is ignored by the instrument and no error code is returned. QUERY Sets the remote pressure (from 500 to 2500) Sets the remote control voltage in % (from 0 to 100) Memorizes the value as P1 to be used in left position Memorizes the value as P2 to be used in right position Sleep mode (stops pump and fan) Resets the values of P1 and P2 to factory settings AVAILABLE ACCESSORIES ACCESSORY PART...

If found to be defective within the warranty period, your Fluigent product will be repaired or replaced free of charge What This Warranty Does Not Cover This warranty does not cover routine maintenance, or damage resulting from the failure to maintain the product in accordance with instructions provided by Fluigent. This warranty also does not cover damage that arises from accidental or intentional misuse or abuse, alteration or customization, or repaired by unauthorized persons. How to Get Service If something goes wrong, contact the Fluigent dealer from whom you purchased your product....

FINDING THE COM PORT NUMBER OF THE DEVICE To find out the COM port number, or narrow down the list to existing ports, go to the device manager (Start menu, either type “device manager” or look for device manager in the control panel). Then go down the list and there should be a COM port categorie Click on the arrow on the left, and the options available should display. If you have several of them and do not know what they are for, try them one by one with a standard query (SYST:IDN?) to see if there is a response. If not, try another one. This can happen when you are using a serial hub or...

FLUIGENT SA O’kabé bureaux 67 avenue de Fontainebleau 94270 Le Kremlin-Bicêtre FRANCE www.fluigent.com +33 1 77 01 82 68 Technical support: support@fluigent.com +33 1 77 01 82 65 General information: contact@fluigent.com For additional information, contact us by email : contact@fluigent.com or consult our website : www.fluigent.co