IP1
15Pages

Index: Description: Technical features: Range and overall dimension of the knobs without pushbutton: Range and electric diagrams of the knobs with pushbutton: Pushbuttons and actuator cap colour option: Page 9 4-way on-off pushbutton: Mounting levers: Wire configuration: Model coding:

KNOB HANDLES IP1 Description: Knobs range type “IP1” includes different shapes as conical and spherical, with threaded or press-fit assembly and are available with or without electric pushbutton. In the standard configuration, the pushbutton is two positions and N.O. on-off circuit. They can be supplied loosen or assembled on levers of different lengths, with standard or customized wiring, with connectors on specific request. The “IP1” knob body is made of black thermoplastic material with good resistance to solvents, oils, greases and other chemical agents. It can be used at low or high...

KNOB HANDLES IP1 Technical features: Shells: Material: UV resistance: Mineral oil resistance: Ambient temperature range: Polyamide Techno polymer (PA) Good Good from -30 to +85°C Levers: Material: Protecting treatment: Steel Galvanizing Pushbuttons: Maximum current: Supply voltage: Electrical life: Mechanical life: Protection degree: Ambient temperature range: Operating force: Total stroke: 5 A resistive, 3 A inductive from 5 to 28 VDC from 25.000 cycles for 5A @ 28 VDC up to 1.000.000 cycles for 1A 1.000.000 cycles IP64 standard (IP68 on request) from -55 to +85°C 7,5±0,2 N 2 mm max....

KNOB HANDLES IP1 Range and overall dimensions of the configurations without pushbutton Standard Spherical knob D50 Spherical knob D47 with stem

KNOB HANDLES IP1 Range and overall dimensions of the configurations without pushbutton

KNOB HANDLES IP1 Range and overall dimensions of the configurations with pushbutton All the overall dimensions are the same of the knobs without pushbutton Standard Spherical knob D50 Spherical knob D47 with stem

KNOB HANDLES IP1 Range and overall dimensions of the configurations with pushbutton All the overall dimensions are the same of the knobs without pushbutton

Pushbutton options: Pushbuttons actuator caps are available in two shapes A (raised) and B (flush) with dimensions and colour options shown below Raised Pushbutton Flush Pushbutton Standard colour option for the actuator caps The colour options shown above are valid for the standard momentary pushbuttons with on-off N.O. circuit, with raised (A) or flush (B) cap actuator without led

KNOB HANDLES IP1 Pushbutton option: Technical features: - Maximum current - Minimum current. - Maximum supply voltage - Electrical life - Mechanical life - Protection degree: - Ambient temperature - Operating angle - Operating force The 4-way pushbutton can be assembled only on knob type ES whose overall dimensions without pushbutton are shown at page 6 of this catalogue. 1 A resistive, 2 A inductive 10 µA @ 30 mV 28 VDC 100.000 cycles 500.000 cycles IP68 from - 55 to + 85°C 10° ±0,5 33±1 N Electric diagram: N Knob with pushbutton MJ4 fitted on lever type 1

KNOB HANDLES IP1 Mounting Levers: Ø12

KNOB HANDLES IP1 Mounting Levers: 20° Knob samples fitted on threaded levers with pushbuttons

KNOB HANDLES IP1 Wire configuration Without wires Single high flexibility, section 0,50 mm² Multicore cable, 2 or 3 wires, section 0,50 mm² Special wire on request (specify features) Wire length Without wires Standard length, from handle bottom (cm) Length on request, from handle bottom (cm) Wire terminals Without wires Wire terminal with 5 mm strip, without tinplate With faston (specify brand and type) Connector (specify brand and type) with wired terminals Wide range of connectors are used for customized wirings

KNOB HANDLES IP1 Model coding: IP1 AP BG N Wire terminals (page 13): - without wires = Z - wire terminal with 5 mm strip, without tinplate = N - with faston (specify brand and type) = S - Connector (specify brand and type) with wired terminals = C Cable length, in cm (page 13): - without wires = 00 - standard length (cm) = 50 - length on request (cm) = XX Wire configuration (page 13): - without wire = Z - single high flexibility, section 0,50 mm² with PVC sleeve = G - Multicore cable section 0,50 mm² (with silicon protection) = M - Special wire on request (specify features) = S Mounting...

THE COMPREHENSIVE RANGE OF MANUFACTURED AND MARKETED COMPONENTS INCLUDES: - Hydraulic gear and axial piston pumps & motors - Directional control valves & selector valves - Proportional EH pressure reducing valves & manifold blocks - Hydraulic, pneumatic and electric on-off & proportional joysticks - Control electronics - Radio controls, push buttons stations, dashboards and armrests - Multifunction ergonomic, cylindrical & palm grips - Hydraulic filters & contamination control systems - Heath exchangers and cooling systems - Fluid monitoring & diagnostic instruments - Bell housings, driving...