Catalogs >
FLOWSERVE >
StarPac 3

StarPac 3
8Pages

Catalog excerpts

StarPac 3 Intelligent Control System

Take Complete Control of your Process with the StarPac 3 The StarPac 3 can improve plant operation at a lower cost than conventional systems. By having the StarPac 3 mounted directly on the valve, along with its associated pressure and temperature sensors, separate line taps are not required. In addition, long straight runs of piping are not required as in the case of conventional methods. The Flowserve StarPac 3 is not just a valve; it is an entire process control system in a single package that includes: • Built-in Process Sensors (P1, P2 and Temperature) substantially reduce process lag...

Open the catalog to page 2

Air Lines to Cylinder Actuator Electronics Module with Keypad and Local Display Temperature Sensor Electronics Conduit Process Pressure Sensors Enhance your Process Control Performance with the StarPac 3 The StarPac 3 control system is offered on a number of Flowserve valve bodies. • • • • • • • • Valtek Mark One - 1 inch to 24 inch (consult factory for larger sizes) Kammer Valves - 1/2 inch to 8 inch Valtek Mark 100 Flowserve Multi-Z Trim Valtek ShearStream - 2 inch to 16 inch Valtek MaxFlo - 2 inch to 24 inch (consult factory for larger sizes) Kammer - SmallFlow and TotalFlow In addition,...

Open the catalog to page 3

Quickly Congure the StarPac 3 Locally or Remotely Complete local conguration can be done using the on-board keypad. Conguration software not required. Additional keypad functionality includes: • Local alarm and error messages • Calibration • System tuning Complete conguration can be done using infrared communications with a PDA that contains the Flowserve keypad simulator software. • Same functionality as the keypad. The StarPac 3 can also be connected to a PC or laptop through a USB Port. The StarPac 3 is provided with the powerful StarTalk XP software. The software is a powerful tool that...

Open the catalog to page 4

Prevent Costly Downtime with StarPac 3’s Diagnostic Capabilities Data Log Friction Signature The StarPac 3 noties you when internal system problems and process problems through: • Continuous Self Diagnostics – Notication of alarms and errors instantly. • Discrete Output – Alarm Relay will activate when selected alarms occur. • On board data logger – Captures 300 data points of process and valve information including ow rate, upstream pressure, downstream pressure, temperature, valve position, valve command, setpoint and process variable The StarTalk XP software is a powerful tool that aids...

Open the catalog to page 5

StarPac 3 System Schematic PC for Diagnostics or Data Acquisition Electrical Pneumatic Mechanical DCS for Operating and Tuning Parameters RS-485 Serial Digital Communication (RS-485) Loop Types P P1 P2 Temp. Flow Position Auxiliary Discrete Digital Signals Position Sensor Input Output Special Options Stainless Steel Gauges psi (bar, kPa) Stainless with Brass Internals psi (kg/cm2) Stainless Steel with Stainless Internals psi (kg/cm2) No Gauges No Specials Fail open, feedback spring bias No Sensors Conduit Connections Aluminum, white paint Stainless, No paint General Purpose Explosionproof...

Open the catalog to page 6

StarPac 3 Specications Table I: Flow Accuracy The accuracy of the standard StarPac 3 model is +/- 2 percent of full scale ow over the turndown of the control valve, normally 30:1 for a globe valve. This can be improved by using characterized trim or reducing the turndown of the high accuracy range. Table II: Electrical Specications Power Supply Nominal 24 VDC (18 to 64 VDC allowable) providing 150 mA (50 mA if only Modbus communications are being used) Analog Inputs Analog Outputs Two (2) 4-20 mA that each drive up to 750 Ω Discrete Input Jumper selectable input voltages of 120 and 24 V...

Open the catalog to page 7

Flowserve Corporation Flow Control Division 1350 N. Mt. Springs Parkway Springville, UT 84663 USA Phone: +1 801 489 8611 Flowserve (Austria) GmbH Control Valves-Villach Operation Kasernengasse 6 9500 Villach, Austria Phone: +43 4242 41 181 0 Flowserve India Controls Pvt Ltd. Plot #4, 1A, E.P.I.P., Whiteeld Bangalore Kamataka India 560 066 Telephone: +91 80 284 10 289 Flowserve Singapore Pte. Ltd. 12 Tuas Avenue 20 Singapore 638824, Singapore Phone: +65 6879 8900 Flowserve Australia Pty. Ltd. 14 Dalmore Drive Scoresby Victoria 3179 Australia Phone: +61 9759 3300 Flowserve Pittsburgh 1300...

Open the catalog to page 8