Catalogs >
Flowserve SIHI Pumps >
Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C
8Pages

Catalog excerpts

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C - 1

Volute Pumps SIHISuperNova ZLIC 040160 . . . 150200 TECHNICAL DATA Output: Head: Speed: Material: Temperature: Casing pressure: Shaft seal: Flange connections: Sense of rotation: max. 280 m³/h max. 60 m max. 3600 rpm grey cast iron: 0B, 0C stainless steel: 4B mat. design: 0B, 0C, 4B max. 120 °C PN 16 / PN 10 1) standard mechanical seal DIN 2501 PN 16 clockwise, when looking at the pump from the drive end Volute pumps of the series ZLIC in inline design have been constructed as space saving and easy to install pumping units with standard motor. The pumps are used when clear resp. turbid liquids without any solid particles have to be pumped without problem. The combination of: - performance and connection size according to DIN 24255 /EN 733 and additional size DN 25 - construction type: INLINE design with standard motor - material: grey cast iron, stainless steel - casing: inline or volute casing (see list ZLK) Casing pressure: was leading to widely spread application fields like · steel, machine and automobile construction · food and semi-luxuries industry · chemical and petrochemical industry · pharmaceutical industry · lacquer industry · plastics and rubber industry · iron and non-ferrous metal industry · paper and pulp-industry · textile industry DESIGN Single-stage resp. two-stage pumping units in compact design with nominal performances according to DIN 24255 / EN 733 as well as additional size DN 25, where suction and discharge branch are arranged opposite to direct installment into the pipework. There is no common shaft for motor and pump. The motors used are of the standard type listed. Thanks to the process design it is possible to withdraw the whole insert unit without removing the casing of the pump from pipework. By means of the unit construction system of the additional size DN 25 the single-stage and the two-stage design have the same dimensions. The performance of the pump is optimally adapted to the service point by mounting and dismounting of a stage. The individual shafts of the unit connected by a plug-in coupling facilitate the dismantling or the replacement of the motor without affecting the pump. The programme comprises. 15 pump sizes at present. 1) For Material design 4B max. 16 bar from -40 °C to 120 °C 0B, 0C max. 16 bar from -30 °C to 120 °C Please note: Technical rules and safety regulations. Casing pressure = inlet pressure plus delivery head + zero flow Flanges location: Suction and discharge flange radially arranged opposite to each other. Flanges: The flanges correspond to DIN 2533 PN 16. Flange drilled ANSI 150 lbs. on request. Hydraulic: First hydraulic. Designation of this construction type: A. Second hydraulic. Designation of this construction type: B. Bearing: Two grease-lubricated antifriction bearings according to DIN 625 in the motor, one antifriction bearing grease-lubricated for service-life according to DIN 625 arranged in the bearing bracket. Designation of this construction type: .K, .V Sense of rotation: Clockwise when looking at the pump from the drive end. Shaft sealing: The shaft sealing is a single mechanical seal, flushed from internal source, uncooled and unbalanced. Designation AAE: cast chrome / carbon, O-rings Perbunan temperature range: -40 °C to 120 °C Designation BH3: SiC / carbon, elastomer EP temperature range: -20 °C to 120 °C Designation BHS: SiC / SiC, elastomer Viton temperature range: -20 °C to 120 °C

Open the catalog to page 1

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C - 2

Material design Material DIN DIN materialmaterialnumber denomination 23.00 Impeller Shaft seal 43.30 Mechanical seal 1) 1) US denomination ASTM Standard O-rings of PTFE upon request; Casing seal: Material design 0B, 0C: Material design 4B: The casing is sealed by a flat gasket of EWP 210. Designation of this construction type: 2 The casing is sealed by a flat gasket of PTFE. Designation of this construction type: 4 Motor power: Using commercial electric motors, type of construction IM B5 resp. IM V 1 To determine the drive power we recommend the following safety margin: up to 4 kW: 25 % 4...

Open the catalog to page 2

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C - 3

Sectional drawing and nomenclature shaft sealing designation BH3 BHS shaft sealing designation AAE volute casing casing cover mechanical seal shaft bearing bracket impeller Standard set of components / bearing bracket - plug coupling / standard motor* / space requirement By supplementing the standard set of components consisting of pump casing, casing cover, impeller and mechanical seal by a special bearing bracket (DBP) results an inline pumps which is easy to combine. The bearing bracket removes the standard motor from the load of hydraulic forces and allows suitable motor combinations at...

Open the catalog to page 3

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C - 4

Designs are subject to amendment without prior notice. © (Sterling Fluid Systems BV) 2005

Open the catalog to page 4

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C - 5

Dimension table Motor Size Designs are subject to amendment without prior notice. © (Sterling Fluid Systems BV) 2005

Open the catalog to page 5

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C - 6

Motor Size Designs are subject to amendment without prior notice. Weight abt. kg Pump Motor 4B 18 37 24 Standard motors as per DIN 42677. Truth of rotation, centricity and right angle of shaft ends and mounting flanges to DIN 42955, normal precision. * Motors protection type IP 55 Dimensions depend on the motor make © (Sterling Fluid Systems BV) 2005

Open the catalog to page 6

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C - 7

Data regarding pump size Type Pump size Hydraulic + Bearing A § First hydraulic B § Second hydraulic § K, V Two grease-lubricated antifriction bearings in the motor. One grease-lubricated antifriction bearing in the bearing bracket. Shaft sealing Material design Casing seal AAE: Standard mechanical seal, O-rings Perbunan 0B: Main parts of cast iron GG25. BH3: Unbalanced mechanical seal, SiC-Carbon, elastomer EPDM bellows. 0C: Main parts of cast iron GG25, Bronze G-CuSn10 BHS: Unbalanced mechanical seal, SiC/SiC, elastomer Viton bellows. AAE, BH3, BHS BH3, BHS 4B: Main parts of stainless...

Open the catalog to page 7

Catalogue - Series ZLI, 280 m³/h, 60 m, 120 °C - 8

COPYRIGHT WARNING Please read this notice The material you are viewing in this document is protected by Copyright and may only be used in accordance with Copyright, Designs and Patent legislation. It is not permitted to copy - either in full or in part - nor substantially extract, reproduce or re-use any of the contents of this document in any material form or in any medium without permission from the Copyright holders or their assignees. Any unlawful use of the material in this document may result in claims for civil remedies, including an injunction to restrain further use and a claim for...

Open the catalog to page 8