…simple flow solutions in a complicated world Medium Series Technical Specifications Screwed Unit A scaled dial and mechanical indicator continuously monitor the flow rate at any given time whilst electrical switches can be specified to signal when a particular level has been reached during increasing or decreasing flow rates. Minimum Scale; Maximum Scale; Style; Flanged Unit Through its unique modular design it allows for easy field installation and service. It does not require any straight pipe runs before or after the monitor thus minimizing the installation footprint. The versatile design of the vane monitor allows for orientation to be mounted in any position. Vane style monitor operates when flow is introduced through the inlet connection making direct contact with the vane that is mechanically linked to the indicator shaft. The fluid forces the vane to move through a contoured opening creating a variable orifice, the greater the flow the larger the orifice becomes for flow to pass. The vane style monitor is spring loaded and allows the vane to return on decreasing flows. Are field adjustable, suitable for batching, trending, totalising or recording where required. All Flow-Mon units can be supplied with a 0-10v or 420mA output. All sizes are manufactured to the same simple design concept, the main characteristic of which ensures that the pressure drops are confined to an absolute minimum (see “pressure drop” charts) across the vane orifice at full flow, with viscosities as high as 600cS. Sizes are defined by pipe size and/or maximum flow capacity, and every flow switch is individually calibrated so that full scale deflection is used in each application i.e. the maximum scale reading coincides with the maximum requirements of system as specified by the customer. Calibration may be in any units with Single or Dual scale to specification. Water, De-Ionised Water, Soluble Oils (Glycols), Petroleum Based Fluids, Synthetic Based Fluids, Coolants, Corrosive Fluids, Paints, Solvents, Air & Gases Medium Series Comparable to similar style devices in the industry, Flow–Mon’s “flow through” design offers a low pressure loss. To ensure accuracy they are individually calibrated in any unit of measure to customer operating specifications. Explosion Proof Aluminium En

SERIES AND FLOW RATE FMC* = Low Flow FMB* = Imp. Gallons / Min FMG* = U.S. Gallons / Min *Add Full Flow Rate in Units MATERIAL OF MANUFACTURE AL = Aluminum CI = Cast Iron CIK = Cast Iron Nickel Plated S = Carbon Steel SS = Stainless Steel PTFE = PTFE *Only available up to 4” Port Connections and 100 psi / 7 bar maximum pressure. Note: For materials and pressures not specified, please consult factory. ‘O' RING SEAL MATERIAL S1 = Buna (-40°C PORT CONNECTIONS PRESSURE RATING LP = 300 psi / 20 bar maximum Sizes 1/4” - 2" are Screwed or Flanged. For Flanged...

Medium Series Installation and Maintenance Instructions Installation Instructions; The flow indicators are in-line devices. Mounting can be in any position, and no straight length of pipe is required before or after the unit. The unit is sandwiched between two flanges. Under the Pressure Equipment Directive (PED) these products are Pressure Accessories, and are not approved for use as safety Accessories, as defined by the PED. If used for safety purposes, it is the responsibility of the user/installer to assess the suitability of the product in the pressure equipment or system in which it is...

Medium Series Spares Data When ordering spares, please give reference number followed by quantity required. All orders should be accompanied by a model number and a serial number of the Flow switch! Description Stud & Nuts O-Ring S1, S2, S3, S4 Centre Housing AL, B, CI, CIK, S, SS, PVC Mounting Disc Enclosure Box Switch 3EE, 3EEG, 4EE, 6EE, 3EE(ATEX3), 3EE(ATEX2), 6EE(ATEX2), AIR, POT, OUT, DIG, TOT Dial Plate Screw Pointer (a) Rear O-Ring (b) Front O-Ring Face Plate Screw Plug Valve Plate Bowl Spares Kit Item No. Qty 2. 2-off For further information contact: Tel: 01423 561972 Fax: 01423...