Group: Xylem
Catalog excerpts
09 Ventilation Blowers INTRODUCTION Jabsco DC Blowers are designed to remove fumes from the engine compartments of gasoline powered boats prior to start-up, and therefore conform to ISO 8846 MARINE and USCG Regulations for ignition protection. They are listed as N.M.M.A. type accepted and comply with ISO 9097 MARINE and are CE marked. AC models are not ignition protected. Jabsco Blowers can also be used for air intake or extraction in galleys, bilges, accommodation and head compartments. Only the heavy-duty blowers are designed for continuous duty operation in commercial or heavy use applications. Blowers should not be installed close to sources of direct heat exceeding 180°F (55°C). Flangemount Blowers Flangemount Blowers are of a radial design, which gives the highest output in more complex installations with longer ducting lengths and/or multiple bends in the ducting. They are generally mounted directly onto a flat bulkhead using a mounting collar to connect to the discharge ducting. This allows a very neat installation on an engine room bulk head. Flexmount Blowers Flexmount Blowers are also of radial design, but are installed by attaching a mounting collar (supplied with the blower) around the motor to any convenient solid surface. They can be rotated inside the collar to allow the shortest ducting lengths and most convenient routings in confined spaces. Both ports are designed for slip-on flexible ducting connections.
Open the catalog to page 1Ventilation Blowers 09 HEAVY-DUTY RADIAL BLOWERS Sizing Definitions Flangemount Heavy-Duty Flangemount Blowers Heavy-Duty Flexmount Blowers Heavy-Duty Flangemount Blowers are designed for applications such as commercial or high-use engine room ventilation and extraction where a longlife requirement demands heavy-duty motors with long brush life. Built to provide the same high outputs as our standard specification blowers. Flexmount Blowers are built to the same high specification as the Heavy-Duty Flangemount Blowers for use as air intake or extraction systems in engine rooms, fuel...
Open the catalog to page 209 Ventilation Blowers RADIAL & IN-LINE BLOWERS Flangemount Blowers Range of high-volume air intake or extraction blowers for engine room, fuel compartment, galley or heads. • Outlet flange mounts directly on bulkhead. • Slip-on inlet ducting connection. • Low current draw. • Dimensionally stable, quiet-running Delrin rotors. • Corrosion-resistant materials throughout. • Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection). • ISO 9097 MARINE (Electric Fans). OUTPUT VOLUME MODEL NUMBER FUSE SIZE Flexmount Blowers Range of high-volume air intake or extraction blowers for...
Open the catalog to page 3In-Line Blowers Rule In-Line Blowers provide ventilation for bilges, engine compartments, galleys and heads. Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion-resistant motor housings for long life. Compact and easily installed on any flat surface, Rule In-Line Blowers provide higher air flow and lower amp draw. • Efficient high-volume air flow. Discharge GUNWALE • Quiet operation. • Low amp draw. • Slip-on inlet and outlet ducting connections. • Sealed motor shaft for moisture protection. • Corrosion-resistant...
Open the catalog to page 4All FLOJET catalogs and technical brochures
-
HPR10/15
2 Pages
-
GP50/25
2 Pages
-
GP28/11
2 Pages
-
GP20/12
2 Pages
-
VFLO 5.0
2 Pages
-
Searchlights
8 Pages
-
General Purpose Pumps
8 Pages
-
Oil Change & Diesel
6 Pages
-
Washdown Pumps
2 Pages
-
Water Pressure Systems
10 Pages
-
Toilet Systems
14 Pages
-
Livewell/Baitwell Pumps
6 Pages
-
Bilge Pumping Systems
24 Pages
-
Speciality Products
6 Pages
-
Sliding Vane Pumps
2 Pages
-
Oscillating Lobe Pumps
2 Pages
-
Lobe Pumps
3 Pages
-
Hand Pumps
2 Pages
-
Flexible Impeller Pumps
29 Pages
-
Diaphragm Pumps
16 Pages
-
Centrifugal Pumps
17 Pages
-
INTERNATIONAL Beverage
15 Pages
-
4100 series
2 Pages
-
C Series
4 Pages
-
5000 Series
2 Pages
-
U Series
2 Pages
-
M502052
2 Pages
-
International Industrial Pumps
100 Pages
-
PS Series
2 Pages
-
SPC42
2 Pages
-
GP20/22
2 Pages
-
GP20/18
2 Pages
-
V100, 060 & 040 V-Jet
5 Pages
-
Bottled Water System Plus
2 Pages
-
LF Plus Series
2 Pages
-
V125 V-Jet
2 Pages
-
Flojet Beverage Catalogue
43 Pages
-
FLOJET BevJet Brochure
12 Pages
Archived catalogs
-
F100-218F
51 Pages
-
pt6_7_8Gear_Hand_LobePumps
8 Pages
-
pt5B_FlexibleImpellers
26 Pages
-
pt5A_FlexibleImpellers
15 Pages
-
Diaphragm_DrumPumps
29 Pages
-
Centrifugal Pumps
37 Pages
-
pt1Cover
11 Pages
-
Flojet Industrial Catalogue
24 Pages