System information Conveyor with focus on robustness and cleanliness Improved cleanliness conveyor The stainless steel conveyor X300X was designed to suit the requirements of food and packaging applications: The X300X conveyor system has been evaluated based on field experience and suggestions from customers. With focus on structure rigidness and robustness, easy design, and easier cleaning, several components have been improved with features like better drainage and smaller contact surfaces. Noise level at 60 m/min is 68 dBA or less Technical characteristics Drive unit capacity Chain tension limit Beam width Chain width Chain pitch Item width Maximum item weight Maximum weight on conveyor Maximum conveyor length System information

Conveyor chain Plain chain * Link kit contains 10 links, 10 pivots, 10 steel pins Chain accessories Use the online configurator to specify and order. *Note. Links are delivered as a kit containing 10 links and the necessary steel pins and plastic pivots. Other chains See the Chain guide for selection of other chains. Pin insertion tool for chain *This tool is recommended for frequent users Plastic pivot for chain Stainless steel Conveyor chain

Conveyor Beam Length 3 m (3000 ±1,5 mm) Length to order (150- 2999 mm) All X300X beams are delivered fully assembled. Conveyor beam type Y, 300 mm 312 300 37,5 Conveyor Beam Length 3 m (3000 ±1,5 mm) Length to order (150- 2999 mm) All X300X beams are delivered fully assembled. Screw Kit 5114562 included Beam spacer kit, Stainless steel Beam spacer kit for X300X Including screws. Additional beam stiffness can be obtained by using additional beam brackets. The beams have predrilled 8,3 mm holes at 100 mm intervals that need to be increased to 10 mm. Conveyor beams

Connecting bracket kit Stainless steel Connecting bracket kit for X300X Including screws. The beams have predrilled 10 mm holes, see XBCBX 3A85. Beam section for chain installation Beam section for chain installation. XBCCX 300A300 Including 2 Connecting bracket kit XBCJX A300 Conveyor beams

Slide rails Plastic slide rails, wide Slide rail Length 25 m HDPE (Black) PE-UHMV (White) PVDF (Transparent white) PA-PE (Grey) (Should not be used in wet applications) XBCR 25 B XBCR 25 UB XBCR 25 PB XBCR 25 HB Note. The wide slide rails are not suitable for use in bends. Mounting tool for slide rail Nut with threaded hole (M8) for connection of sensors and other accessories when the conveyor chain is in place. By placing nuts inside the beam at the holes, accessories can be attached using M8 A4 screws. NOTE! Be careful when installing so no nut is dropped inside the beam, this can lead to a...

Slide rails (continued) Rivet crimping pliers Rivet crimping clamp Rivet crimping pliers For 4 mm rivets 23 Rivet crimping clamp For 4 mm rivets (note: Allen key not included) Tools for conveyor beam Drill fixture Drill fixture Twist Drills DIN 338 HSS-E (Co 8) Type N-HD Cobalt Alloyed, Split Point Drill 11,0 mm Drill 10,2 mm Drill 8,3 mm Drill 4,5 mm Drill 4,2 mm (for 3920500) For use when additional holes are needed on the beam sides. Including: Drill 4,5 mm Drill 8,3 mm Drill 11,0 mm and instructions for use. For high strength alloys on CrNi base such as Hastelloy, Inconel, Monel, Nimonic,...

Drive and idler units - introduction Drive unit types The X300X system drive unit capacities is maximum 1250 N. The actual capacity depends on the speed. Available motors include variable speed types (V) as well as fixed speed motors (F). Motor specifications or 330/575 V, 60 Hz. Variable speed motors are SEW Movimot, 380-500 V. Note that variable speed motors include a control box that adds 93 mm to the width of the IP class 65 and available with standard oil and food Idler unit types XLX Idler units are available in two versions, Compact and Standard. xssx Drive units with motors must be specified...

Drive units – configuration strings Below, two examples of text strings obtained from the configurator with explanations are presented. Drive unit with fixed speed motor Drive unit with variable speed motor Item no - Drive type XBEBX: H – Motor power ... kW: Motor power, kW (position is omitted for variable speed motors see position F) B – Motor position L: Left R: Right I – Thermal protection No: No thermal protection TF: Thermal protection type TF TH: Thermal protection type TH (position is omitted for variable speed motors) J – Hybrid cable C – End drive with guided chain G: Guided (position...

End drive units End drive unit, direct drive, no slip clutch End drive unit, guided chain, no slip clutch End drive unit Direct drive with guided chain. No slip clutch. Maximum traction force: up to 1250 N. Maximum speed 80 m/min for X300X. End drive unit Direct drive. No slip clutch. Maximum traction force: up to 1250 N. Maximum speed 80 m/min for X300X. Motor on left side: Motor on left side: Fixed/variable speed * Without motor Fixed/variable speed * Without motor Motor on right side (not shown): Fixed/variable speed * Without motor Fixed/variable speed * Without motor Motor on right side...

Idler unit Idler end unit Idler end unit, Compact 25 Effective track length: 0,70 m. Effective track length: 0,35 m. Protective cover for Idler end Protective cover for Idler end, Compact 323 300 Protective cover for Idler end unit XBEJX A300 Protective cover for Idler end unit XBEJX A300 S Note! Always use protective cover for Idler ends to protect persons from clamp risk. Idler unit

Bridges, drive unit to idler unit Bridge, idler compact to drive unit Bridge, idler to drive unit 166 Including roller bridge and mounting hardware. Suitable for connecting idler compact to drive unit. Including roller bridge and mounting hardware. Suitable for connecting idler to drive unit. Note! Bridges 5115194-5115199 can only be used with plain chain! PO Bridges, drive unit to idler unit

Plain bends Item no Effective track length Support rail for plain bends Support rail for plain bends, Length 2,4 m Polyamide Fix with sheet metal screw ISO 7049 4,2×9,5 or similar. Plain bends