System information Chain travels on four slide rails. Wide track sideflexing safety chain. Compact horizontal and vertical bends. Suitable for soft packages. Examples of application areas Large cardboard boxes, products in soft plastic bags. Examples: detergent powder, wrapped tissue paper rolls, food products, personal care products. System information

Conveyor modules Straight conveyor Support modules – single and multi-lane L Multi single 2 lane Multi single 3 lane Multi single 4 lane Multi double 3 lane Multi double 4 lane Conveyor module – straight * *Use online configurator when ordering L1 Conveyor module – one bend * *Use online configurator when ordering L2 Conveyor module – two bends * *Use online configurator when ordering Conveyor modules

Plain chain Length 3 m XBTP 3A180 K XBTPX 3A180 K Plain link kit * FLX1004629 *Link kit contains 10 links, 10 pivots, 10 steel pins Friction top chain Length 3 m PAR 1 Friction top chain Length 3 m PAR 2-20 XBTP3A175F XBTP 3A175 FP Use the online configurator to specify and order. Friction top link kit * 5056653 *Link kit contains 10 links, 10 pivots, 10 steel pins Other chains See the Chain guide for a selection of other chains. Chain installation See Appendix C, page 527, for installation instructions. Roller cleat link -175 - Roller cleat link 5056654 Roller cleat chain must be ordered as...

Pin insertion tool for chain Pin insertion tool Beam components X180 Beam section Beam (outer section) Beam section (assembled) Length to order (500- 2995 mm) XBCB LA180 Slide rail: see page 282 Beam (outer section) Length to order (500- 3000 mm) XBCB LA H Beam (mid-section) Profile for split conveyor beam (inner section) Beam (mid-section) Length to order (500- 3000 mm) XBCB LA85 Profile for split conveyor beam Length 3000 +10/-0 mm XBCB 3A85 H Length to order (500- 3000 mm) XBCB LA85 H

Beam components X180 (continued) Mounting tool for clip kit Clip kit for outer beam sections Snap-fit clip kit for outer beam sections Each kit contains two clips. For construction of 182 mm wide beam sections. Mounting tool: see below. Maximum distance between clips is 0,5 m. Mounting tool for aluminium clip kit XBCE 40 3923518 Beam section for chain installation Beam clip assembly Beam clip assembly Beam section for chain installation Including connecting strips and screws Including M8 screw and locking nut. Use minimum 5 clips per meter. Place clips 100 mm from each end. Note. Contains 10...

Slide rails X180 Plastic slide rail for X180/X300 beam Plastic screws for slide rail Slide rail Length 25 m HDPE (Black) PA-PE (Grey) PVDF (Natural white) XBCR 25 XBCR 25 H XBCR 25 P See Appendix A, page 517 for selection guidelines and assembly instructions. Plastic slide rail for X180/X300 beam, outer Plastic screws 5 mm for XS-X65-X85XH-X180-X300 beams XLAG 5 See mounting instruction “Anchoring slide rail using plastic screws” on page 522 Note. Contains 50 pcs. Drill fixture for slide rail Slide rail, outer UHMW-PE (μ=0,1–0,25) (White) Length 3 m Drill fixture for X65-X85-XH-XKX180-X300 slide...

Drive and idler units - introduction PO The X180 system includes direct driven units with or without slip clutch. Available motors include variable speed types (V) as well as fixed speed motors (F). Motor specifications Motors are available for 230/400 V, 50 Hz and 230/460 V or 330/575 V, 60 Hz. All motors can be connected for delta or star configuration by means of jumpers. Variable speed motors are SEW Movimot, 380-500 V. Note that variable speed motors include a control box that adds 93 mm to the width of the motor. Drive units with motors must be specified using the web-based configurator....

End drive unit, direct drive End drive unit, direct drive, slip clutch End drive unit, direct drive Fixed speed up to 60 m/min Variable speed up to 80 m/min Motor on left side Fixed/variable speed * XBEB A180 End drive unit, direct drive Fixed speed up to 60 m/min Variable speed up to 80 m/min Motor on left side Fixed/variable speed * XBEB A180 Without motor XBEB 0A180HLP Motor on right side Fixed/variable speed * XBEB A180 Maximum traction force: 1250 N. See page 22. Effective track length: 0,80 m *Use online configurator when ordering. Motor on right side Fixed/variable speed * XBEB A180 Without...

End drive units X180, direct drive, slip clutch, guided End drive units X180, direct drive, no slip PO clutch, guided -CC End drive unit H, guided chain, no slip clutch X45 Direct drive with guided chain. Adjustable slip clutch. Maximum traction force: up to 1250 N. Fixed speeds up to 60 m/min. Variable speed up to 80 m/min. Motor on left side: Direct drive with guided chain. No slip clutch. Maximum traction force: up to 1250 N. Fixed speeds up to 60 m/min. Variable speed up to 80 m/min. Motor on left side: Fixed/variable speed * XBEB A180 Motor on right side: Fixed/variable speed * XBEB A180...

Idlers X180 Idler end unit 182 Effective track length: 0,80 m Protective cover for idler end unit Protective cover for idler end unit

Bridges Passive bridge from conveyor to conveyor Attachment wire Passive bridge* From: Heavy Drive Wire for attaching roller to holder FLX1006041 *Also available as a configuration option through XBNG A180. To: Heavy Idler * Use online configurator when ordering. XH Passive bridge to or from machine or application, Single or double rollers Bridge in position sensor kit Conveyor to conveyor External to/from Conveyor *Also available as a configuration option through XBNG A180. *Note Bridges can not be used with cleated chain. Passive bridge* Single roller (1) or Double roller (2) XBNG A180 From:...

Plain bend, 30° Plain bend, 30°±1° Effective track lengths: Effective track lengths: Plain bend, 60° Plain bend, 60°±1° Effective track lengths: Effective track lengths:

Four outer section beam pieces, unassembled. Effective track length: 0,50 m (top+bottom) Four outer section beam pieces, unassembled. Effective track length: 0,75 m (top+bottom) Four outer section beam pieces, unassembled. Effective track length: 1,5 m (top+bottom)