Conveyor system WL374X
1 / 16Pages

System information System overview FlexLink's newly developed stainless steel conveyor is designed to fit into demanding primary and secondary packaging applications. It addresses important aspects of today's packing processes, such as being easy to clean, smooth handling of products, safe for operators, robust design, long life, and easy to maintain with a low cost of ownership. The modularized and standardized design ensures fast set up, and facilitates rapid future extensions and changes. Separation of larger surfaces To simplify cleaning and to ensure consistent results, larger surfaces have been separated to improve access between them for cleaning and inspection of results. This separation also improves drainage and speeds up the drying process after cleaning. Also, the bearings are separated 25 mm from the framework with spacers to prevent contamination. System information

Small contact surfaces No flat surfaces for better drainage To make the cleaning process faster and consistent, the small contact surfaces within the frame have been designed in order to eliminate hard-to-reach areas. In wash-down environments, it is important to have proper drainage of water and other liquids. The WLX design has been optimized in this regard by selecting different manufacturing processes to create shapes that enable efficient drainage. This will also have an important impact on its ability to be cleaned in dry environments in both primary and secondary packaging lines. No...

Conveyor sections 7. End drive units The modular plastic belt conveyor in three widths – 374, 526 and 678 mm – can be built as straight sections or in S, U or L-shape with 30, 45, 60 or 90° horizontal bend, or combinations thereof. Vertical bends are available in 5° positiv or negative. Kit for conveyor beam end, always included in: - End drive units - Idler end units - Plain bends - Vertical bends Conveyor sections

Modular Belts - Introduction Outer slide rail Slide rail Belt guide Lower cross bar Modular belt, Radius flush grid, curve-running The belt consists of plastic hinged links connected by plastic rods. The belt is woven together by links that are 102 mm, 124 mm, and 180 mm wide. The assembled belt forms a wide, flat, and tight conveyor surface. Three standard widths of belt can be delivered: 304 mm, 456 mm, and 608 mm. Standard belt color is white but blue belts can also be ordered. Belts with polyamide pins are available for dry or semiwet applications. In constant wet applications, belts...

Modular belts Radius flush grid belt, Dry Plain belt Belt material Acetal (POM) Pin material Polyamide (PA), brown Length 1 m 304 mm wide, White 304 mm wide, Blue Flat top belt Belt material Acetal (POM) Pin material Acetal (POM), white Length 1 m 304 mm wide WLTP 1B304 W Radius flush grid belt, Wet PO Plain belt Belt material Acetal (POM) Pin material Acetal (POM), white Length 1 m 304 mm wide, White 304 mm wide, Blue Belt tensioner tool for radius flush grid CSX Belt tensioner tool Modular belts

Conveyor Beams - Introduction Components such as plain bends, etc., cannot be placed too close to an End drive unit. Therefore, the minimum permissible length for conveyor beam sections when connecting to an End drive unit is 844 mm. This ensures a sufficient amount of return belt tension directly after the drive sprocket to avoid slack close to the sprocket wheel. The return belt hanging between the first two belt guides provides this belt tension (called back tension). Connecting brackets have to be ordered separately when joining End drives, idler ends, conveyor beams, etc. When joining...

Technical specifications Minimum permissible conveyor beam length to be connected: With belt tensioner unit In order to simplify the cleaning process FlexLink can offer belt lift arms for straight conveyors. Contact FlexLink for more information. WLCBX 3A Standard length 3000 mm 6 mm space, easy to clean 6 mm space, easy to clean WL 678X WLCBX LA L = 1700 mm 6 mm space, easy to clean Top belt travel direction Conveyor Beams - Introduction

Conveyor frame components Beam spacer Kit for WL374 Conveyor beam, Easy Clean Conveyor beam, WL374X Length 3 m (3000 ±1,2 mm) WLCBX 3A374 Length to order (142 - 2999 mm) WLCBX LA374 * Use online configurator when ordering Effective track length: 2,1 m Beam spacer kit Recommended Torx tool for fasten spacer Size: T30 Connecting Bracket For beam Including 4 pcs M10 screws Beam support brackets 56 Beam support bracket (A) Including 6 pcs M10 screws Beam support bracket (B) Conveyor frame components

Slide rail Slide rail Slide rail, length 3 m Slide rail (A) Outer slide rail (B) Connecting Strip x4 x4 Connecting strip kit WLAHX 100 Must be ordered in multiples of 10 Drill fixture for connecting strip Contains drill fixtures for both WLCRX 3 and WLCRX 3B Slide rail

Belt tensioner unit A belt tensioner unit should always be placed near the End drive unit and its use is recommended: - for long conveyors >20 meters - for long conveyors >15 m and a speed of >30 m/min - for conveyors with frequent starts/stops, especially if the load is high - if an End drive unit needs to be placed close to a plain bend - if an End drive unit needs to be placed on the lower part next to a conveyor slope section Direct drive, no slip clutch - for short conveyors where the belt slack length is insufficient to lift the belt for cleaning Drive unit types Drive unit types A...

Drive units – configuration strings Below are two examples of text strings obtained from the configurator with explanations. Drive unit with fixed speed motor Drive unit with variable speed motor Item no - Drive type WLEBX: I – Thermal protection No: No thermal protection TF: Thermal protection type TF TH: Thermal protection type TH (position is omitted for variable speed motors) J – Hybrid cable No: No hybrid cable C: Hybrid cable included in SEW Movimot (position is omitted for fixed speed motors) B – Motor position L: Left R: Right K – Fieldbus D – Speed V...: Fixed speed... m/min V......