SSimno fixture works

Yfv ONE-TOUCH SPINDLE LOCKS QUICK SHAFT-LOCKING CLAMPS PNEUMATIC SHAFTLOCKING CLAMPS PNEUMATIC SHAFTLOCKING CLAMPS Pricing, ordering and CAD downloads available at fixtureworks.com

Pricing, ordering and CAD downloads available at fixtureworks.com

ONE-TOUCH SPINDLE LOCKS Plastic Knob Supplied With 2 of Flat round washer(Stainless Steel) Pricing, ordering and CAD downloads available at fixtureworks.com fixture works

■One-touch Spindle Locks enable quick and secure locking of shafts with one click of the knob. ■When One-touch Spindle Lock is operated, the knob clicks and the shaft is locked with a steady force. This provides reliable locking of shafts. ■The knob position and the indication line clearly indicate lock/unlock position. Technical Information One-touch Spindle Locks can fix both revolving and sliding of shafts. Note: The above information is for cold finished S45C steel bars with tolerance h7. Use this only as a guide. ■Allowable tightening torque for mounting screws IQCSPLI04 Size: 1.5 N ■ m,...

QSC QUICK SHAFT-LOCKING CLAMPS Body / Handle Part Number Part Number Pricing, ordering and CAD downloads available at fixtureworks.com

Supplied With Four hex. socket setscrews ■As the handle is turned down, it pushes the locking block toward the shaft for clamping. When the handle is released, the flat spring allows the locking block to be returned to the original position. ■Both faces can be used for installation. Two sides with two tapped holes can also be used for installation(remove the setscrews). Do not give hammer taps to the handle or extend the handle with a pipe or the like for easier clamping, to avoid any damage. Dimensions between the shaft-hole center and the sides are not precise. When installing a Quick Shaft-Locking...

QUICK SHAFT-LOCKING CLAMPS (Pneumatic) imno 2-For di Cap Screw (Both Sides) Body / Cover Plate ★One Point-n [ Clamping by spring pressure/Unclamping by air pressure ^ ^imno fixture in arks Pricing, ordering and CAD downloads available at fixtureworks.com

■ How to Operate Slide the clamp over the shaft at the unclamped mode, and then fix the body using the 2 mounting holes. Screwing the plug completely into the hole allows locking the shaft. Supplying air allows compressing the spring to get the shaft unlocked. Releasing the air allows getting the spring to work to lock the shaft. Feature ■Air pressure to be applied : 0.5 - 0.7MPa Recommended to use with a three-way valve. ■The mechanism of spring-pressure clamping and air-pressure unclamping prevents shaft-locking force from getting lowered. ■Connecting air plumbing to multiple Quick Shaft-Locking...

PNEUMATIC SHAFT-LOCKING CLAMPS RrmjJC w 11J ★Key Point - For automation of shaft locking. Low pressure type also available. Part Number Pricing, ordering and CAD downloads available at fixtureworks.com

Application Example ■Three-way valves are recommended. ■ Use bushings or bearings with the unit as needed. ■Spring clamping and pneumatic unclamping mechanism prevents the decrease of clamping force by air leakage. ■Available for remote and multiple operations. ■Perfect for use in limited space. ■IPSLC-3L1 type can be used with 0.3 MPa air pressure. ■Clamping/unclamping operations must be performed with the shaft not in motion. Cannot be used as a brake of a moving shaft. ■ Do not force the clamped shaft to move. ■ Do not operate frequently without the shaft. ■Manual unclamping is not possible....

PSLC-M,PSLC-M-S PNEUMATIC SHAFT LOCKING CLAMPS PSLC-M,PSLC-M-S PNEUMATIC SHAFT LOCKING CLAMPS 2-M3X0.5 Mounting Hole for Sensor Brackets ★Key Point -s For automation of shaft locking. Usable with sensors. v___/ *) Delivered with the setscrew installed. See the Feature section for details. **) Recommended shaft: Heat treated (over HRC50) or hard chrome plated (over HV750, over 10iim thickness) Pricing, ordering and CAD downloads available at fixtureworks.com

Supplied With ■Spring clamping and pneumatic unclamping mechanism prevents the decrease of clamping force by air leakage. ■Available for remote and multiple operations. ■|PSLC-M-S| type can be used in combination with sensors to detect the clamping condition. The sensors must be supplied separately by customer. ■For details on applicable sensors and installation details, refer to |PSLC-M-SBl-■Can be unclamped manually. The clamp can be released without air supply by fully tightening the setscrew into the manual unclamping hole. ■A setscrew is attached to the pneumatic port for shipping. Remove...

PSLC-M-SB SENSOR BRACKETS Part Number *) Magnetic Proximity Sensors manufactured by ASA ELECTRONICS INDUSTRY CO., LTD. L-shaped sensors cannot be used with these brackets. Please refer to their catalog for details of sensors. Supplied With ■Clamping conditions can be detected by using applicable sensors. ■Sensor must be supplied separately by the customer. 2 of M3x0.5-5L Hex socket button head screw IPSLC-M-SIPNEUMATIC SHAFT LOCKING CLAMPS (Sensor Mountable) ■ Remove the screws from the sensor cases with a slotted screwdriver and fix the sensors to Pneumatic Shaft-Locking Clamps using iPSLC-M-SBl...

Pricing, ordering and CAD downloads available at fixtureworks.com