Catalogs >
FISHER REGULATORS >
Pressure Equipment Directive (PED) Classification Guide for Regulator Products

Pressure Equipment Directive (PED) Classification Guide for Regulator Products
8Pages

Catalog excerpts

Pressure Equipment Directive (PED) Classification Guide for Regulator Products - 1

Pressure Equipment Directive (PED) Classification Guide for Regulator Products Introduction The Pressure Equipment Directive (PED) 2014/68/EU requires pressure equipment destined for Europe to have a CE mark and that the equipment meet all aspects of the directive except where noted for SEP. The PED is a directive that applies to the design, manufacture and conformity assessment of pressure equipment and pressure assemblies. All equipment covered by the directive must comply with essential safety requirements and meet the equivalent national laws of all member countries. PED Classification To ensure that products destined for Europe meet the requirements of PED, it is necessary to determine the proper PED classification. In the PED, pressure equipment can be classified in one of the following categories: • SEP (Sound Engineering Practice) • Category I • Category II • Category III • Category IV SEP Products The SEP classification applies to pressure equipment that is not subject to Category I, II, III or IV conformity assessment, but must be designed and manufactured with “sound engineering practice” as defined by the PED. SEP classified products do not and cannot receive a CE mark. Product Classification Use Tables 1 to 5 to find the PED category of a specific product. Note Any specific type number, body size or body material not included in the PED Product Classification table is not available for sale into Europe. Products can only be processed per classification specified in the PED Products Classification table. Due to PED Classification limitations, some products may not be available at full rated pressures. Be sure to check the PED Limitation column in the PED Product Classification table. PED Documentation Documentation Fisher™ branded products destined for Europe will contain an Installation Guide in the language requested or in the language of destination. If a language is not requested or the destination is unknown, English, German and French Installation Guides will be included. Documentation On-Line PED Installation Guides in the desired language are available on the internet for immediate viewing and downloading. To access: go to www.emerson.com, locate and click the CE mark button (see Figure 1). Subsequent screens will display available PED Installation Guides. The PED Installation Guides may be downloaded in .pdf format. (To view a .pdf file, Acrobat Reader software must be installed on your computer. Acrobat Reader software latest version i

Open the catalog to page 1

Pressure Equipment Directive (PED) Classification Guide for Regulator Products - 2

PED Table 1. PED Classification for Products Manufactured in McKinney or FROMEX(1) SERIES OR TYPE BODY MATERIAL All All All Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel All All All All All All All Steel, Stainless steel Steel, Stainless steel All All Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel Cast iron Steel All All All Steel All All All All All All All All All All All All All Ductile iron, Cast iron, Steel Ductile iron, Cast iron Steel All Steel Steel 1. Please consult factory for other products not listed in this...

Open the catalog to page 2

Pressure Equipment Directive (PED) Classification Guide for Regulator Products - 3

PED Table 1. PED Classification for Products Manufactured in McKinney or FROMEX(1) (continued) SERIES OR TYPE BODY MATERIAL All Steel, Stainless steel All All All All Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel Steel, Stainless steel All All All All All All All All All All All All Stainless steel Stainless steel Stainless steel Steel Steel All Brass All All 1. Please consult factory for other products not listed in this Bulletin. 2. Size refers to inlet...

Open the catalog to page 3

Pressure Equipment Directive (PED) Classification Guide for Regulator Products - 4

PED Table 1. PED Classification for Products Manufactured in McKinney or FROMEX(1) (continued) SERIES OR TYPE LR125 LR128 MR95H/HD/HDP MR95HP/HT MR95L/LD MR98H/HD/HDP BODY MATERIAL Steel, Stainless steel Cast iron Cast iron Steel, Stainless steel, Hastelloy® C Cast iron Steel, Stainless steel, Hastelloy® C Cast iron Steel, Stainless steel Cast iron Steel, Stainless steel Ductile iron Cast iron Steel, Stainless steel, Hastelloy® C Cast iron Steel, Stainless steel, Hastelloy® C 1. Please consult factory for other products not listed in this Bulletin. Hastelloy® C is a mark owned by Haynes...

Open the catalog to page 4

Pressure Equipment Directive (PED) Classification Guide for Regulator Products - 5

PED Table 2. PED Classification for Products Manufactured in FROMEX(4) or Cluj, Romania(1) SERIES OR TYPE CS400 and CS404 BODY MATERIAL Ductile cast iron Cast steel Ductile cast iron Cast steel Ductile cast iron, Cast steel Ductile cast iron, Cast steel Cast Iron Ductile iron WCC steel Ductile iron WCC steel All except Cast iron All except Cast iron All except Cast iron CATEGORY I (without slam shut) IV (with slam shut) I (without slam shut) IV (with slam shut) I (without slam shut) IV (with slam shut) I (without slam shut) IV (with slam shut) I (without slam shut) IV (with slam shut)...

Open the catalog to page 5

Pressure Equipment Directive (PED) Classification Guide for Regulator Products - 6

PED Table 3. PED Classification for Products Manufactured in Gallardon, France or Cluj, Romania(1) SIZE BODY MATERIAL Zinc/Aluminum Alloy Ductile iron WCC Steel, LCC steel Ductile iron Inlet: Sphero-conical or flat joint connection Outlet: Flat meter joint connection Inlet: Sphero-conical or flat joint connection Outlet: BS746, ISO228 Internal x External GAS NPT, SWE, CL150 RF, CL300 RF, CL600 RF, BWE, PN 16/25/40 NPT, SWE, CL150 RF, CL300 RF, CL600 RF, BWE, PN 16/25/40 NPT, SWE, CL150 RF, CL300 RF, CL600 RF, BWE, PN 16/25/40 NPT, SWE, CL150 RF, CL300 RF, CL600 RF, BWE, PN 16/25/40 CL150,...

Open the catalog to page 6

Pressure Equipment Directive (PED) Classification Guide for Regulator Products - 7

PED Table 4. PED Classification for Products Manufactured in Bologna, Italy or Cluj, Romania(1) (continued) SIZE BODY MATERIAL Cast steel Steel, Stainless steel All BSP, PN 16/25/40 UNI/EN CL150/300 RF BSP, PN 16/25/40 UNI/EN CL150/300 RF BSP, PN 16/25/40 UNI/EN CL150/300 RF CL300 RF, CL600 RF, UNI/EN PN 6 NPT Cast iron 1. Please consult factory for other products not listed in this Bulletin. 2. Size refers to inlet (PAD) connection. Table 5. PED Classification for Products Manufactured in Shanghai, China(1) SERIES OR TYPE BODY MATERIAL 1. Please consult factory for other products not...

Open the catalog to page 7