Vibration Systems and Engineering Ltd.

ELECTRICAL SPECIFICATION : POWER ( Watt ) VOLTS ( Volt ) CURRENT ( Amps ) MECHANICAL SPECIFICATION : MODEL SPRING FRONT Quantity x mm SPRING REAR Quantity x mm SPEED Cm/sec CAPACITY SPECIFICATION : WEIGHT VIBRATOR TRAY WEIGHT SPEED Cm/sec MODEL NOT : Yukarıdaki kg teknik değerler kanal konulmadan sadece vibratörden alınmıştır. mm kg Tons / hour Lt / min

CAPACITY, TRAY WIDTH, PRODUCT DENSITY VEM1 Electromagnetic linear feeder with standard tray dimensions : Height : 40 mm , width: 80 mm , lenght : 300 mm The above figure shows the variation of the tray capacity, depending on the height of product.. VEM2 Electromagnetic linear feeder with standard tray dimensions Height : 60 mm , width: 130 mm , lenght : 500 mm The above figure shows the variation of the tray capacity, depending on the height of product..

CAPACITY, TRAY WIDTH, PRODUCT DENSITY VEM3 Electromagnetic linear feeder with standard tray dimensions : Height : 80 mm , width: 150 mm , lenght : 700 mm The above figure shows the variation of the tray capacity, depending on the height of product.. VEM4 Electromagnetic linear feeder with standard tray dimensions Height : 80 mm , width: 200 mm , lenght : 800 mm The above figure shows the variation of the tray capacity, depending on the height of product..

All metallic parts in 304 stainless steel, Fibreglass springs lifetime guaranteed, Heat resistant sealings, ( 250° C ) Water and heat resistant coil (with polyurethane resin 200° C ) (with polypropylene housing 120° C ) Single screw for air gap adjustment High or slow speed selection, Frequency range 3000 rpm – 6000 rpm Sensitive adjustment with potentiometer

Depending on product and its speed of feeding, air gap adjustment is very important. The air gap is the spacing that exits between the armature and magnet assembly. Back side of vibrator there is a nut. Loose the nut before starting adjustment. Screw the screws clockwise, until it comes to the end of the stroke and so right in time with the drive. Loosen the screw counter clockwise, with reference to table ‘ Mechanical Spec.’, determine the adequate air gap for your feeder. So turn the screw so many times as necessary to obtain the required air gap. Tighten the nut to maintain the set screw tightly....

VEM1-39 Coil Space Ring 1

All metallic parts in 304 stainless steel, Fibreglass springs lifetime guaranteed, Heat resistant sealings, ( 250° C ) Water and heat resistant coil (with polyurethane resin 200° C ) (with polypropylene housing 120° C ) Single screw for air gap adjustment High or slow speed selection, Frequency range 3000 rpm – 6000 rpm Sensitive adjustment with potentiometer

Depending on product and its speed of feeding, air gap adjustment is very important. The air gap is the spacing that exits between the armature and magnet assembly. Back side of vibrator there is a nut. Loose the nut before starting adjustment. Screw the screws clockwise, until it comes to the end of the stroke and so right in time with the drive. Loosen the screw counter clockwise, with reference to table ‘ Mechanical Spec.’, determine the adequate air gap for your feeder. So turn the screw so many times as necessary to obtain the required air gap. Tighten the nut to maintain the set screw tightly....

Silicon Reduction Static Equipment, Body Trough Screw for Air Gap Setting Gap Setting Fix Pin Seating Coil Cover Coil Silicon Ring Leaf Assembly Leaf Space Plate Leaf Fixing Plate Antivibrating Leg Anti Electric Cable M8 Nut M20 Nut M8 x 25 Bolt Pg 7 Cable Gland M5x8 Bolt M5 Spring Washer M8 Spring Washer M5x16 Bolt M8x35 Bolt M8x30 Bolt Silicon Outer Ring Coil Space Ring

All metallic parts in 304 stainless steel, Fibreglass springs lifetime guaranteed, Heat resistant sealings, ( 250° C ) Water and heat resistant coil (with polyurethane resin 200° C ) (with polypropylene housing 120° C ) Single screw for air gap adjustment High or slow speed selection, Frequency range 3000 rpm – 6000 rpm Sensitive adjustment with potentiometer

Depending on product and its speed of feeding, air gap adjustment is very important. The air gap is the spacing that exits between the armature and magnet assembly. Back side of vibrator there is a nut. Loose the nut before starting adjustment. Screw the screws clockwise, until it comes to the end of the stroke and so right in time with the drive. Loosen the screw counter clockwise, with reference to table ‘ Mechanical Spec.’, determine the adequate air gap for your feeder. So turn the screw so many times as necessary to obtain the required air gap. Tighten the nut to maintain the set screw tightly....

Silicon Reduction Static Equipment, Body Trough Screw for Air Gap Setting Gap Setting Fix Pin Seating Coil Cover Coil Armature Silicon Ring Leaf Assembly Leaf Space Plate Leaf Fixing Plate Antivibrating Leg Anti Electric Cable M10 Nut M8 Nut M20 Nut Pg 7 Cable Gland M8 Spring Washer M10 Spring Washer M5x16 Bolt M8x20 Bolt M10x50 Bolt M10x40 Bolt

All metallic parts in 304 stainless steel, Fibreglass springs lifetime guaranteed, Heat resistant sealings, ( 250° C ) Water and heat resistant coil (with polyurethane resin 200° C ) (with polypropylene housing 120° C ) Single screw for air gap adjustment High or slow speed selection, Frequency range 3000 rpm – 6000 rpm Sensitive adjustment with potentiometer

Depending on product and its speed of feeding, air gap adjustment is very important. The air gap is the spacing that exits between the armature and magnet assembly. Back side of vibrator there is a nut. Loose the nut before starting adjustment. Screw the screws clockwise, until it comes to the end of the stroke and so right in time with the drive. Loosen the screw counter clockwise, with reference to table ‘ Mechanical Spec.’, determine the adequate air gap for your feeder. So turn the screw so many times as necessary to obtain the required air gap. Tighten the nut to maintain the set screw tightly....