Catalogs >
FIAM >
Automatic screw presenters

Automatic screw presenters
16Pages

Catalog excerpts

Tightening automation With the efficiency of pick and place. Automatic screw presenters Screw suction systems • For automatic and manual use

Open the catalog to page 1

Tightening systems with automati for very fast and efficient tighteni When carrying out manual assembly with small screws on the bench or an automatic assembly line, tightening time is essential to increase productivity. These automatic screw feed systems significantly reduce cycle times and can be used in both manual pick-and-place and automatic processes. In fact the screws can be picked up easily by a magnetic bit or by a screw suction system, ready for immediate tightening. The models offered provide a flexible solution to most application situations that can arise in normal industrial...

Open the catalog to page 2

ic screw presenter: ing. ASSEMBLY EXAMPLE WITH MANUAL PHASES ASSEMBLY EXAMPLE WITH A SCREW PRESENTER TOTAL TIME TOTAL TIME SCREW PICK-UP SCREW POSITIONING TIGHTENING SCREW PICK-UP SCREW POSITIONING TIGHTENING SCREW PICK-UP TRANSFER TIGHTENING SCREW PICK-UP TRANSFER TIGHTENING SCREW PICK-UP TRANSFER TIGHTENING PIECE UNLOADING SCREW PICK-UP SCREW POSITIONING TIGHTENING PIECE LOADING SCREW PICK-UP TRANSFER TIGHTENING PIECE LOADING SCREW PICK-UP SCREW POSITIONING TIGHTENING PIECE UNLOADING TIME SAVED: 4 seconds The great productivity of these systems guarantees a return on the investment in a...

Open the catalog to page 3

Manual pick-and-place systems • For magnetisable screws with PHILLIPS or POZIDRIV recesses and lengths up to 18 mm • For straight air and electric screwdrivers with lever start The pick-and-place systems for manual use consist of NJ screw presenters to ensure fast, smooth work cycles, helping to reduce production costs. The benefits: • No manual steps: operators do not have to pick up screws manually and place them on the screwdriver bit, reducing cycle times by over 24%. • Very convenient to use: just pick the screw up from the selection channel with the screwdriver, leaving the other hand...

Open the catalog to page 4

Manual and automatic pick-and-place systems • or screws made of any material, even non-magnetisable with lengths up to F 18 mm • or all recess types F • or screwdrivers with screw suction systems F • or nutrunner motors with screw suction systems and that are installed on F slides or robots NJR screw presenters are very versatile because the screw suction system with which the coupled tools must be equipped means they can be used in a multitude of manual and automatic applications. The benefits: • They can be used with any screw type, including those with Torx or hexagonal recesses: the...

Open the catalog to page 5

Technical features PHILLIPS BITS POZIDRIV BITS For screws with shank Ø mm Phillips screws Pozidriv screws Bit dimensions in mm • .35 mm bits with 6 hexagonal drive (ISO 1174) and Phillips/Pozidriv tip SCREW SUCTION SYSTEM For screws with shank Ø mm • With any recess • Special bits with lengths different from those in the drawing To choose the screw suction system and tool be paired with it, see pages 12 onwards. Technical features Models available upon request Standard equipment (provided with the presenter) • Feed voltage: 240 V, 50/60 Hz • Operating voltage:15 Volt c.c. • Brushed DC motor...

Open the catalog to page 6

How to choose the screw presenter Check the screw type and geometry: - the shank diameter must be in the range 2 mm to 5 mm - the shank maximum length must be less than/equal to 18 mm Types of screws * Without washer * With washer Choose the model according to the screw diameter * With double washer Nominal screw Screw diameter diameter ** With flat or oval countersunk head Screw head diameter Washer diameter Screw head Screw shank height length Decide if the process is manual or automatic and check whether the screw material is magnetisable or not. Screw size supported (screw diameter) Use...

Open the catalog to page 7

Manual Pick-and-place with rotary screw selection system • or magnetisable steel screws from M2 to M6, with under-head lengths up F to 25 mm • For air and electric screwdrivers with magnetised bits and lever start • To pick and place screws with the magnetised bit Manual pick-and-place systems that incorporate OM26-M screw presenters feature a rotary screw selection system that separates the screws one by one and positions them at the pick-up point. The benefits: • Efficient pick-up exploiting the magnetised bit, aided by the pick-up “well”. • Ease of use for the operator, who can easily...

Open the catalog to page 8

Automatic Pick-and-Place with rotary screw selection system • For magnetisable steel screws from M2 to M6, with under-head lengths up to 25 mm • For all recess types • For screwdrivers with screw suction systems • For nutrunner motors with screw suction systems and that are installed on slides or robots OM-26R screw presenters with rotary screw selection system, for positioning at the pick-up point, can be used in automatic pick-and-place processes. The benefits: • Convenient pick-up point on the rotating escape: screws from the linear rail, are placed at the pick-up point one by one,...

Open the catalog to page 9

Technical features Models for manual use PHILLIPS BITS POZIDRIV BITS For screws with shank Ø mm Phillips screws Pozidriv screws Bit dimensions in mm • .35 mm bits with 6 hexagonal drive (ISO 1174) and Phillips/Pozidriv tip Models for automatic use OM-26R MODELS For screws with shank Ø mm upon request upon request upon request upon request upon request upon request upon request SCREW SUCTION SYSTEM To choose the screw suction system and tool be paired with it, see pages 12 onwards. • With any recess • Special bits with lengths different from those in the drawing Technical features Models...

Open the catalog to page 10

How to choose the screw presenter Check the screw type and geometry: - the shank diameter must be in the range 2 mm to 6 mm - the shank maximum length must be less than/equal to 25 mm Types of screws * Without washer * With washer Choose the model according to the screw diameter * With double washer Nominal screw Screw diameter diameter ** With flat or oval countersunk head Screw head diameter Washer diameter Screw head Screw shank height length Decide if the process is manual or automatic. The screw must be magnetisable. Screw size supported (screw diameter) Use Screw material Magnetisable...

Open the catalog to page 11