Catalogs >
FIAM >
Air screwdrivers 15C

Air screwdrivers 15C
16Pages

Catalog excerpts

Core innovation Straight, pistol and angle 15C air screwdrivers and nutrunners Torque range: from 0,4 to 5 Nm Automatic shut-off Body perfection

Open the catalog to page 1

Searching for excellence, developing ideas. Are you looking for innovation, practicality and accuracy? Only the range of 15C tools can satisfy your needs. A modern range, ideal in every type of industrial assembly: to overcome the performance’s challenge with different control levels of the whole assembly process. For this reason each 15C tool is also designed to monitor the assembly cycle (poka-yoke system, anti-error system) or the joint, ensuring extraordinary results. 15C screwdrivers: perfection has a new name and a new number. Screwdrivers and nutrunners with TRACS2 torque control...

Open the catalog to page 2

Control levels of the assembly process Level 2 Level 1 Torque control Torque control, screws counting • TRACS2 CLUTCH • ACCURATE TIGHTENINGS • HIGH REPEATABILITY • COUNTING OF TIGHTENED SCREWS • ACCURATE TIGHTENINGS • OK / KO CYCLE • HIGH REPEATABILITY • MONITORING OF THE TIGHTENING TIME Angle nutrunner

Open the catalog to page 3

15C screwdrivers/nutrunners with TRACS2 torque control An eye for innovation, a glance to the future. For over 65 years Fiam has been moving towards the future and research. So it has designed the modern 15C air screwdrivers/ nutrunners, increasing quality and performances. Straight, pistol and angle tools are characterized by their extreme handiness and ergonomic grip: ideal for working with high productivity and minimum effort. Modern solutions ideal in mechanical, electrical, electronics and furniture fields. Long start lever. The handling of the tool is easier Comfortable and reduced...

Open the catalog to page 4

Comfortable and reduced effort reverse cursor Ergonomic grip with no slip sheath for safe and comfortable tool holding ROLLBOX reduction gear system Low effort button with gradual starting system TRACS2 torque control system Quick-change chuck with easy and safe use Our name, your guarantee. For each model. 1 2 Technologically advanced MOTRIX air motor, ensuring higher performances. Patented TRACS2 torque control system; it guarantees high torque repeatability and vibration levels below 2,5 m/s2. ROLLBOX reduction gear system, ensuring high output. Practical cycle end acoustic signal....

Open the catalog to page 5

Don't be satisfied with the maximum Reliability Long lifetime of the components thanks to careful design and to quality of the productive process which results in less maintenance and repair costs 1 TRACS2 (Torque Repeatability and Accuracy Control System): the torque control system ensures a very high torque repeatability, i.e. a very low Mean Shift value also in the presence of variability of the joint softness level. This system maintains same torque values for hundreds of thousands of cycles. TRACS2 system guarantees a high quality improvement in the tightening process 2 MOTRIX: newly...

Open the catalog to page 6

Perfection is in your hands Naturally innovative Optimization of the tool performances in regard to ergonomics and operator safety PISTOL GRIP Minimal dimensions: these tools can be used in every position and when space is limited. Their handling is guaranteed because the grip is very near to the tool’s head Weight: extremely reduced weight and compact dimensions guarantee perfect handling Ergonomic grips: designed according to modern biomechanics principles paying particular attention to the features of the female hand. The grips are manufactured with an ergonomic sheath made of...

Open the catalog to page 7

f Tightening torque ' on softjoint 15 = Power of the motor in Watt/10 • C = Screwdriver/Nutrunner • 2 = Maximum tightening torque in Nm • A = Air shut-off system • L = Lever • P = Pistol grip • 30 = Head at 30° • 90 = Head at 90° • PA = 'Forward' pistol grip Reversibility: all models are suitable for tightening and untightening operations Lever start Push start Push button The figures shown are measured at a pressure of 6,3 bar (ISO 2787) the recommended operating pressure. Tightening torque values have been measured in accordance with ISO 5393 standard. Noise level has been measured in...

Open the catalog to page 8

Supplied black colour- 0 wire 2,2mm Code 595102204 Assembled on the tool grey colour- 0 wire 3,2 mm Code 595103202

Open the catalog to page 9

15C screwdrivers/nutrunners with TRACS2 torque control + SCREWS COUNTING 0% error, 100% accuracy. Did you lose any screws? The 'screws count' function will help you: therefore in case of high production rate, you won't risk any omission. Moreover, the feed-back signal and the end one to pass to next piece accelerate the production cycles and ensure control on the assembled products. So dead times will decrease and quality will increase. The solution includes: • Lever or push button air shut-off 15C SCREWDRIVERS equipped with pneumatic pick-up signal (ported) • COMPUTERIZED MONITORING UNIT...

Open the catalog to page 10

TOM needs to be purchased along with Fiam transducer, one for each tool (except when TOM is connected to EasyDriver CA). Completely designed and manufactured by Fiam, it is a single box that receives two pneumatic signals (input) through two hoses of different colors: black for starting signal and green for torque signal; equipped with led indicator and unique electric connecting cable (output) to carry the electrical signal to the TOM unit. Reduced dimensions and weight, easier to calibrate.

Open the catalog to page 11

• 8 for programmes selection, 6 for remote functioning: switching off, program activation, tool stop, tool loosening, program reset Availables with contacts 24V/GND (both pull-up and pull-down) for a great compatibility with the bench buttons (i.e: reset, block, unblocking etc.) and to be interface with the PLC of the client • For results, active program, screwdriver status and possible electro-valve activation, auxiliary output, signal waste piece, in cycle signal (to check the beginning and the end of tightening cycle, useful i.e. set/unset the pieces jigs) Automatic check of tightening...

Open the catalog to page 12

Legend 15 = Power of the motor in Watt/10 • C = Screwdriver/Nutrunner • 2 = Maximum tightening torque in Nm • A = Air shut-off system • L = Lever • P = Pistol grip • 30 = Head at 30° • 90 = Head at 90° • PA = 'Forward' pistol grip • 2CS = Double-signal pressure Legend U Reversibility: all models are suitable for tightening and untightening operations Lever Push button • The figures shown are measured at a pressure of 6,3 bar (ISO 2787) the recommended operating pressure. • Tightening torque values have been measured in accordance with ISO 5393 standard. • Noise level has been measured in...

Open the catalog to page 14