Catalogs >
FIAM >
26C Air screwdrivers

26C Air screwdrivers
20Pages

Catalog excerpts

Speed. Efficiency. Accuracy. Straight, pistol 26C air screwdrivers • Torque range: from 0,4 to 12 Nm • Automatic shut-off

Open the catalog to page 1

Searching for excellence, developing ideas. Are you looking for innovation, practicality and accuracy? Only the range of 26C tools can satisfy your needs. A modern 260 Watt power range, ideal in every type of industrial assembly: to overcome the performance’s challenge with different functionality levels and thanks to the control of the whole assembly process. For this reason each 26C tool is also designed to monitor the tightening cycle (poka-yoke system, anti-error system) or the assembled component, ensuring extraordinary results. Screwdrivers with TRACS2 and TRACS3 torque control...

Open the catalog to page 2

Control levels of the assembly process Level 2 Level 1 TRACS2 and TRACS3 torque control. TRACS2 and TRACS3 torque control + screws counting. • TRACS CLUTCH • ACCURATE TIGHTENINGS • HIGH REPEATABILITY • TRACS CLUTCH • COUNTING OF TIGHTENED SCREWS • ACCURATE TIGHTENINGS • OK / KO CYCLE • HIGH REPEATABILITY • MONITORING OF THE TIGHTENING TIME Pistol UpGrip screwdriver

Open the catalog to page 3

26C screwdrivers with TRACS2 and TRACS3 torque control All Fiam innovation in your hands For over 65 years Fiam has been moving towards the future and research. So it has designed the modern 26C air screwdrivers, increasing quality and performances. Straight, pistol and pistol UpGrip tools are characterized by their extreme handiness and ergonomic grip: ideal for working with high productivity and minimum effort. Modern solutions ideal in mechanical, electrical, electronics and furniture fields. Hanging ring for balancer use Possibility of conveying air exhaust Predisposition for pneumatic...

Open the catalog to page 4

Evident and incisive cycle end acoustic signal for operator Technologically advanced MOTRIX air motor, ensuring higher performances Hanging ring for balancer use Recyclable materials Safe, practical and precise clutch adjustment system The design of the new comfortable and reduced effort reverse cursor permits higher bump resistance and manoeuvrability Ergonomic grip with no slip sheath for safe and comfortable tool holding Quick-change chuck with easy and safe use Patented silencing system ROLLBOX reduction gear system, ensuring high output Patented TRACS 2 and TRACS3 (Torque Repeatability...

Open the catalog to page 5

Don’t be satisfied with the maximum Long lifetime of the components thanks to careful design and to quality of the productive process which results in less maintenance and repair costs Considerable increase of the efficiency of the tightening cycle thanks to innovative systems MOTRIX: newly conceived air motor ensures long lifetime, high specific power and maximum torque MOTRIX: innovative project principles guarantee a higher rotating speed of the new air motor with equal tightening torque, with evident reduction of tightening cycle time ROLLBOX: new reduction gear system has been designed...

Open the catalog to page 6

Perfection is in your hands Naturally innovative Optimization of the tool performances in regard to ergonomics and operator safety Ergonomic grip: designed according to modern biomechanics principles paying particular attention to the features of the female hand. The grip is manufactured with an ergonomic sheath made of no slip material making it easier to hold the screwdriver, increasing the hand grip, improving the handling, the thermal isolation and operator’s comfort TRACS2 and TRACS3: the modern torque control systems reduce the reaction to the operator’s hand. Thanks to the immediate...

Open the catalog to page 7

Tightening torque on soft joint Models with Pistol UpGrip 26C4APU Models with reversibility next to starting button 26C4APA-2000-R Models with reversibility next to starting button and triple air inlet 26C4APA3I Models with threaded drive for screw suction system 26C4A- FT

Open the catalog to page 8

Legend 26 = Power of the motor in Watt/10 • C = Screwdriver • 4 = Maximum tightening torque in Nm • A = Air shut-off system • L = Lever start • P = Pistol grip • PA = ‘Forward’ pistol grip • PU = UpGrip pistol grip • 2000 = Idle speed • R = Reversibility • 3I = 3 Inlets (3 air inlets) • FT = (Front Thread) Equipped with threaded drive for screw suction system N.B.: Reversibility cursor can be positioned on the right or left of the start button. Legend Reversibility: all models are suitable for tightening and untightening operations • The figures shown are measured at a pressure of 6,3 bar...

Open the catalog to page 9

26C screwdrivers with TRACS2 and TRACS3 torque control + SCREWS COUNTING 0% error, 100% accuracy. Did you lose any screws? The ‘screws count’ function will help you: therefore in case of high production rate, you won’t risk any omission. Moreover, the feed-back signal and the end one to pass to next piece accelerate the production cycles and ensure control on the assembled products. So dead times will decrease and quality will increase. • Lever or push button air shut-off 26C SCREWDRIVERS equipped with pneumatic pick-up signal (ported) • COMPUTERIZED MONITORING UNIT TOM (Tightening...

Open the catalog to page 10

Tightening Operation Monitor Model Electric feed Monitoring unit width 208 x depth 128 x height 42 Standard equipment • Feeder • Feed cable • Use and maintenance manual • Eco-friendly packaging TOM Tightening Operation Monitor is also available in the configuration BOX TOM, that includes: TOM unit and all its accessories already wired in a single box. This “Plug and Play’ solution is easy to introduce into assembly lines and extremely practical since you just need to connect the air line and the power supply to start production immediately. Model Electric feed Monitoring unit h 265 mm...

Open the catalog to page 11

• 8 for programmes selection, 6 for remote functioning: switching off, program activation, tool stop, tool loosening, program reset Availables with contacts 24V/GND (both pull-up and pull-down) for a great compatibility with the bench buttons (i.e: reset, block, unblocking etc.) and to be interface with the PLC of the client • For results, active program, screwdriver status and possible electro-valve activation, auxiliary output, signal waste piece, in cycle signal (to check the beginning and the end of tightening cycle, useful i.e. set/unset the pieces jigs) AUTOMATIC CHECK OF TIGHTENING...

Open the catalog to page 12