Catalog excerpts
Professional Electronic Ballasts Professional Electronic Ballasts 1 for T5 Linear Lamps Professional Electronic Ballasts 5 for T8 Linear Lamps Professional Electronic Ballasts for 9 TCL Linear Lamps Professional Electronic Ballasts for 13 TC-DEL Linear Lamps Basic Electronic Ballasts for Linear Lamps 17 Recommended Lamp Brands / Models 25 for Professional Electronic Ballasts Recommended Lamp Brands / Models 27 for Basic Electronic Ballasts Installation Information for Professional 27 Electronic Ballasts Installation Information for Basic 28 Electronic Ballasts...
Open the catalog to page 2• AC operating voltage 185 - 265V, ignition voltage > 170V • DC operating voltage 196 - 330V, ignition voltage > 240V • High voltage protection >315 VAC • Low voltage protection < 150 VAC • Operation frequency > 40 kHz. • Average service life 50.000h (failure frequency at maximum ta temperature < %0.2 /1.000h) • Has protection for lamp instant failures. • Lamp life protection < 0.7s • It automatically restarts on lamp changes. • Lamp capacitive mode protection > 2.5s • Lamp asymmetric voltage protection > 2.5s • It performs lamp filament control initially and during operation. • It performs...
Open the catalog to page 3Lamp operating characteristic • Warm Start: Lamp cathodes are heated by 1.5s of preheating in the AC and DC supply voltages. Emergency Lighting • It is compatible with the emergency lighting kits defined in the EN 60347-2-3 EK-J. • In energy cuts the stepping in time is 0.5s.
Open the catalog to page 4ta (Operating Temperature) and tc (Test Point) ta and tc points are directly related to the life of ballast, tc value depends on the temperatures that are defined in the ta range. The value of ta is significant for the critical components used in the ballast (For example, electrolytic capacitors). ta and tc values are indicated on the ballast covers. For long operating life, these values should be followed. In addition, the terms of warranty are valid for the declared ta and tc values. 4 p FEDERAL Installation rules Electronic ballasts should be installed inside the lighting armatures in...
Open the catalog to page 5T5 Linear Lamps T5 linear lamps should be applied along with the TRDLIGHT T5 electronic ballasts; the power and length values of T5 linear lamps are provided below. The only way to achieve the maximum efficiency of the system is by using appropriate lamps. The habit of considering only power criteria in conventional T5 Lamp Information The lamp connection diagrams of the electronic ballasts in following models should be as given above. Cable lengths are provided in the table. • TRD5-FDH-1/MW (1x14W) • TRD5-FDH-1/MW (1x35W) • TRD5-FDH-1/MW (1x21W) • TRD5-FDH-1/54 (1x54W) • TRD5-FDH-1/MW...
Open the catalog to page 6• AC operating voltage 185 - 265V, ignition voltage > 170V • DC operating voltage 196 - 330V, ignition voltage > 240V • High voltage protection >315 VAC • Low voltage protection < 150 VAC • Operation frequency > 40 kHz. • Average service life 50.000h (failure frequency at maximum ta temperature < %0.2 /1.000h) • Has protection for lamp instant failures. • Lamp life protection < 0.7s • It automatically restarts on lamp changes. • Lamp capacitive mode protection > 2.5s • Lamp asymmetric voltage protection > 2.5s • It performs lamp filament control initially and during operation. • It performs...
Open the catalog to page 7Lamp operating characteristic • Warm Start: Lamp cathodes are heated by 1.5s of preheating in the AC and DC supply voltages. Emergency Lighting • It is compatible with the emergency lighting kits defined in the EN 60347-2-3 EK-J. • In energy cuts the stepping in time is 0.5s.
Open the catalog to page 8ta (Operating Temperature) and tc (Test Point) ta and tc points are directly related to the life of ballast, tc value depends on the temperatures that are defined in the ta range. The value of ta is significant for the critical components used in the ballast (For example, electrolytic capacitors). ta and tc values are indicated on the ballast covers. For long operating life, these values should be followed. In addition, the terms of warranty are valid for the declared ta and tc values. Installation rules Electronic ballasts should be installed inside the lighting armatures in accordance...
Open the catalog to page 9T8 Linear Lamps T8 linear lamps should be applied along with the T8 electronic ballasts; the power and length values of T8 linear lamps are provided below. The only way to achieve the maximum efficiency of the system is by using appropriate lamps. The habit of considering only power criteria in conventional (magnetic) ballasts is not applicable for the electronic ballasts. Different electronic ballasts should be used for each different power and type of fluorescent lamps. Considering that our products operate at 40 kHz. and above, the lamps to be applied in the system should be suitable...
Open the catalog to page 10• AC operating voltage 185 - 265V, ignition voltage > 170V • DC operating voltage 196 - 330V, ignition voltage > 240V • High voltage protection > 315 VAC • Low voltage protection < 150 VAC • Operation frequency > 40 kHz. • Average service life 50.000h (failure frequency at maximum ta temperature < %0.2 /1.000h) • Has protection for lamp instant failures. • Lamp life protection < 0.7s • It automatically restarts on lamp changes. • Lamp capacitive mode protection > 2.5s • Lamp asymmetric voltage protection > 2.5s • It performs lamp filament control at start and during operation. • It performs...
Open the catalog to page 11Lamp operating characteristic • Warm Start: Lamp cathodes are heated by 1.5s of pre-heating in the AC and DC supply voltages. Emergency Lighting • It is compatible with the emergency lighting kits defined in the EN 60347-2-3 EK-J. • In energy cuts the stepping in time is 0.5s.
Open the catalog to page 12ta (Operating Temperature) and tc (Test Point) tta and tc points are directly related to the life of ballast, tc value depends on the temperatures that are defined in the ta range. The value of ta is significant for the critical components used in the ballast (For example, electronic capacitors), ta and tc values are indicated on the ballast covers. For long operating life, these values should be followed. In addition, the terms of warranty are valid for the declared ta and tc values. <pFEDERAL The ballast - lamp connection cables to be used in armatures shall be performed in accordance...
Open the catalog to page 13All Federal Elektrik catalogs and technical brochures
-
ANALYZER
11 Pages
-
20 relays
6 Pages
-
BMC (Bulk Moulding Compaund)
3 Pages
-
NATURAL GAS METERS
22 Pages
-
FUSE SWITCH DISCONNECTORS
14 Pages
-
NH FUSES and BASES
8 Pages
-
THERMAL OVERLOAD RELAYS
6 Pages
-
SURGE PROTECTIVE DEVICE
8 Pages
-
INSTALLATION CONTACTORS
4 Pages
-
MOLDED CASE CIRCUIT BREAKERS
54 Pages
-
Molded Circuit Breakers
54 Pages
-
Air Type Circuit Breakers
14 Pages
-
NH (H.R.C) Fuses
8 Pages
Archived catalogs
-
NH (H.R.C) Fuses
9 Pages
-
Contactors
22 Pages
-
Natural gas meters
17 Pages
-
Control unit heating system
3 Pages
-
Modular panel system
7 Pages
-
Easypan Distribution Boards
11 Pages
-
Electronic Energy Meters
6 Pages
-
Measurement Devices
12 Pages
-
Reactive Relays
10 Pages
-
Power capacitors
7 Pages
-
Relays
7 Pages
-
Motor protection switches
5 Pages
-
Smart relays
5 Pages
-
Thermal relays
5 Pages
-
Cam switches
5 Pages
-
Current transformers
8 Pages
-
Miniature circuit breakers
8 Pages
-
Vertical type switch fuses
5 Pages
-
Load Break Switch
9 Pages
-
Air Type Circuit Breakers
15 Pages
-
L_V_Circuit_Breakers
53 Pages