AerPOS
49Pages

AerPOS User's Manual Version-0.5 AP-3435 15” Bezel Fanless POS system

Copyright Notice This document is copyrighted, © 2012. All rights are reserved. Firich Enterprise Co., Ltd reserves the right to make improvements of the product described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission from Firich Enterprise Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Firich Enterprise Co., Ltd assumes no responsibility for its use, nor for any infringements upon the rights of third...

Safety and Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall could cause damage. 7. The openings on the enclosure are for air convection. Protect the...

Table of Content Chapter 1 Introduction Chapter 2 Hardware Installation and Upgrading Chapter 3 Software Installation and Setup

Introduction AerPOS ( AP-3435 ) Introduction Bezel Free AerPOS series reaches design concept of the Total Cost Ownership and balance the strong requirement for POS quality, AerPOS is implemented with Quality-Oriented, SpaceEffective, Fanless Energy Saving. AP-3435 also provides a decent choice for noise-free environment applications with optimized product reliability. Main Features: • The high quality of resistive touch or durable tempered glass of projective capacitive touch both are IP65 front panel compliant. Fanless solution for noise-free environment, mobile platform for green and...

15” Touch Display Power Switch HDD LED USB Port Power Switch / Status Blue LED: Power ON Red LED: Power Off / Standby 2.5” SATA Drive Access HDD / SATA Status Orange LED: Operation MSR Finger Print Receiver RFID i-Button Cable Access

Rear I/O Panel Connectivity COM 4 USB Connector Type D-sub 9 DC IN connector DC out connector RJ-45 A type USB D-sub 9 D-Sub 15 RJ-45 A type USB D-sub 25 Serial port COM 1 Connect the 12V power adaptor to this port 12V DC out put connect to 12V peripherals or devices Serial Port COM 4 Connect to standard A type USB devices Serial port COM 2 Connect 2nd LCD screen or CRT monitors Connect to Ethernet Connect to standard A type USB devices Standard LPT (Parallel port) connector for printers or KeyPro solution PS/2 PS/2 connector Connect the keyboard or mouse to this port Cash Drawer RJ-11...

Hardware Installation and Upgrading Do not remove the Display Module without switch off the terminal. Power must be switched off and power cord must be unplugged. Every time you service the system, please be aware of this. 2.5” Hard Disk Drive Installation 1. Turn off power and remove power cord from the terminal 2. Unscrew the maintenance door at the front side of the terminal body 3. Flip the maintenance door and Extract 2.5” SATA storage bracket out (no cable connected) 4. Place storage driver on the bracket and fasten it with 4 screws. 5. Restore the maintenance door to the system. 6....

MSR / Finger Print Reciever / RFID / iButton Installation 1. Remove the plastic cover at the back of Touch Display Module 2. Insert the MSR / RFID / Finger Print Receiver / Ibutton Module into USB AType Connector. Fix the Touch Display Module with one screw. 3. Make sure the USB connected and screw is fastened well. 4. If you are looking for the detail Utility of MCR, Finger Print Reader, I-button Reader, RFID Reader, please contact FEC’s FAE.

COM Port Power Setting 5. Remove back cover of the terminal by two screws on the top side 6. Select COM port Power by jumper 3. Please aware Pin1 location and make sure the correct power voltage is selected for serial devices.

Back Cover Installation Notice According to the Thermal Reliability, please ensure the “Hooks of Back Cover” are well assembled into the terminal main chassis during the remove and re-installation back cover.

1. Remove the VFD Plastic cover and Back Cover on the terminal 3. VFD is connected to the COM6 (COM6 has internal power which has been pre-set as 12V power) ** Please note When VFD/LCM is integrated, please remove the external COM3 from the Rear IO to prevent the serial devices are conflict with each other by using the same COM 3. 5 4. Make sure 12V is selected for COM6 (please aware Pin1 location) 5. Connect the COM 6 internal cable between Terminal and VFD / LCM Module and install the VFD/ LCM module with Terminal. Fasten one screw back and make sure VFD/LCM module is fixed.

6. Tilt and Adjust the VFD / LCM angle into proper position. Memory (DDRIII RAM) Installation Unfasten and remove the back cover Install DDRIII memory Before restore the top cover, please check the thermal pad stays in the same position

Remove the VFD plastic cover Assemble the 2nd screen with bracket with 4 screws Assemble the 2nd Screen with bracket to Terminal. Fasten 3 screws (1 on top, 2 underneath)

15” 1st Touch Display Installation & Swapping Release 1 thumb screw at the back side of Display Lift the Display Module up to disassemble from the main unit of terminal Display and main body units are separated. Reverse the process can assembly back the Touch Display Module. ** please make sure the touch display module is firmly connected to the docking slot ** **Note** During the process of disassembly and installation, please ensure the terminal is “Power Off” and remove AC. “Hot Swap” could activate internal protection to block touch display functionali

OSD Function and Adjustment OSD function and adjustment Back Light Power (finger touch for 2 seconds) Back Light Power On – Blue LED indication Back Light Power Off – Red LED indication Button Down (finger touch for 2 seconds) Back Light Dimmer Down Button Up (finger touch for 2 seconds) Back Light Dimmer Up No Function / Reserve Function for AerTouch Monitor