SPEED CONTROLLERS
19Pages

SPEED CONTROLLERS wall mounted and built-in for AIR INTAKE, VENTILATION and EXTRACTION SYSTEMS FASAR elettronica

ELECTRONIC REGULATORS • Phase cut technology controllers (page 4) p/n FE229 - 4,5 A with motor and light control p/n FE230 - 4,5 A with motor and light control (digital) p/n FE263 8 A with motor and light control p/n FE282 - 10 A with motor and light control p/n FE1023 - 10 A with motor and light control (digital) p/n FE1031 - 4,5 A with motor control p/n FE1032 - 8 A with motor control p/n FE1033 - 10 A with motor control •Inverter technology controllers (page 10) p/n FE1018 single-phase inverter 3,5 A with motor control p/n FE1019 single-phase inverter 8 A with motor control p/n FE1024...

GENERAL FEATURES Advanced control systems, some of them with microprocessor, for the speed adjustment of a 4,5, 8 and 10 A single-phase induction motor. Available with digital, analog and remote control. N.B. The p/n FE230 is available in the basic version (without sensors, without receiver for remote control, without serial communication port RS-485), or: ■ FE230/T: equipped with NTC probe to automatically control the motor speed (the speed changes according to the detected temperature) or with thermal contact to protect the motor wirings; ■ FE230/R: equipped with radio receiver for...

Technical features Speed regulators with motor, light and solenoid valve control

Speed regulators with motor and an optional load control FE1031

ELECTRONIC REGULATORS • Phase-cut technology controllers (Built-in) DIGITAL FE1038 – 4,5 A A practical solution that integrates power board and user interface into a single control unit for fast and easy panel mounting. Controls On request, we can supply the front panel, p/n FE1039 single-phase 4A induction motors (maximum current absorbed by the motor, 900W), lighting system and solenoid valve. FEGR017- 4 A The FEGR017 digital speed controller allows the control of 4A single-phase induction motors (max power absorption 900W), and of an external solenoid valve, the lights and a possible...

ANALOGIC FEGR016 – 4 A With a simple and functional user interface, controller is equipped with optional inputs and outputs for the handling of sensors and any external command, it can control an additional load voltage, and the firmware can be customized. Tasto ON / OFF Motore POLYCARBONATE PANEL p/n FE1016 ANALOG USER INTERFACE 0-10V CONTROL FE1008 – 1,5 A With the possibility to vary the speed of the motor either by means of a potentiometer (optional), or through a 0-10 V analog input: this last option is very useful in a wide range of applications and in particular, if you want to...

ELECTRONIC REGULATORS • Inverter technology controllers The inverter technology provides the best energy efficiency concerning the realization of variable flow systems: it is widely documented that the advantages resulting from the use of inverter are particularly marked in those plants in which the operating cycle is most varied. The use of the inverters also allows to exploit particularly large speed intervals and operation dynamics, to decrease motor’s stress reducing the negative effects caused by acceleration and deceleration transient, to implement protection functions to safeguard...

Advantages of the use of single-phase inverter with induction motors: • Possibility to control the speed efficiently and with wide dynamics: the inverter modulates the motor rotation speed according to the real extraction requirements. • Absence of in line phase shift between voltage (V) and current (I): power factor close to 1. Reduction of the wear rate of the mechanical components of the motor: the soft starts e soft stops reduce the stress on the motor and on the mechanical components (absence of inrush speed during the start phase). Starting with controlled power consumption....

FE1018 - FE1019 motor control (3,5 A - 8 A) The FE1018 and FE1019 (in the picture, the 3,5 A model FE1018) are two models of single-phase frequency converters for the control of induction motors that respectively absorb up to 750 W (max current absorption of 3,5A) and 1500 W (max current absorption 8A) of electrical power. The front panel integrates the on/off switch and a rotary knob to vary continuously the motor’s speed: the microprocessor, which is the heart of the inverter, allows to manage appropriate acceleration and deceleration ramps and to realize protection techniques for...

FE1024 - FE1025 Motor, light and solenoid valve control (3,5 A - 8 A) FE1024 and FE1025 are two models of single-phase frequency converters to control induction motors that respectively absorb up to 750 W (max current absorption of 3,5A), and 1500 W (max current absorption 8A) of electrical power. These devices include a manual switch for the lighting system and the automatic activation of an optional load (safety solenoid valve). A few seconds after the motor activation, the optional load is activated (signaled by a dedicated led). By switching off the motor, the other load is immediately...

ELECTROMECHANICAL REGULATORS • Electromechanical controllers for common wire motors Auto-trasformer for 2 wires single-phase induction motors

CONTROLLERS FOR SUCTION HOODS COMBINED WITH OVENS AND DISHWASHERS WALL MOUNTED FOR DISHWASHER FE230/U with humidity sensor. Is a microprocessor-based system with low consumption when in stand-by. Allows you to control the hood motor in manual or automatic mode by means of probe measurements at the opening of the machine. FOR OVEN HOODS FEGF01 – FEGR021 with temperature probe and microswitch. Allows you to control the hood motor in manual or automatic mode by means of probe measurements at the opening of the machine, or immediately at the oven door opening thanks to the microswitch (for the...

CONTROLLERS FOR SUCTION HOODS COMBINED WITH OVENS AND DISHWASHERS Part Number Maximum load MOTOR Maximum load LIGHTS Phase angle system for the control of the motor ON/OFF control of lights via relay Solenoid valve control Ability to customize the firmware Flat cable 10 poles L=310mm with sheath Polycarbonate mask Microprocessor control system Nr. 1 temperature sensors PT1000 + Nr. 1 microswitch door Motor type Power supply User interface Visual signals Inputs/outputs for probes and/or external control