SPEED CONTROLLERS wall mounted and built-in
12Pages

{{requestButtons}}

Catalog excerpts

SPEED CONTROLLERS wall mounted and built-in - 1

SPEED CONTROLLERS wall mounted and built-in for AIR INTAKE, VENTILATION and EXTRACTION SYSTEMS FASAR elettronica

Open the catalog to page 1
SPEED CONTROLLERS wall mounted and built-in - 2

Air intake and ventilationOur speed regulators for single-phase motors ELECTRONIC REGULATORS (wall mounting) • Phase cut technology Models available p/n FE229 - 4,5 A with motor and light control p/n FE230 - 4,5 A with motor and light control (digital) p/n FE263 8 A with motor and light control p/n FE282 - 10 A with motor and light control p/n FE1023 - 10 A with motor and light control (digital) p/n FE1031 - 4,5 A with motor control p/n FE1032 - 8 A with motor control p/n FE1033 - 10 A with motor control • Inverter technology Models available p/n FE1018 single-phase inverter 3,5 A with...

Open the catalog to page 2
SPEED CONTROLLERS wall mounted and built-in - 3

• Phase-cut technology GENERAL FEATURES Advanced control systems, some of them with microprocessor, for the speed adjustment of a 4,5, 8 and 10 A single-phase induction motor. Available with digital, analog and remote control. The p/n FE230 is available in the basic version (without sensors, without receiver for remote control, without serial communication port RS-485), or: • FE230/T: equipped with NTC probe to automatically control the motor speed (the speed changes according to the detected temperature) or with thermal contact to protect the motor wirings; • FE230/R: equipped with...

Open the catalog to page 3
SPEED CONTROLLERS wall mounted and built-in - 4

Technical features Speed regulators with motor, light and solenoid valve control Technical features Speed regulators with motor and an optional load control FE1031

Open the catalog to page 4
SPEED CONTROLLERS wall mounted and built-in - 5

ELECTRONIC REGULATORS  Inverter technology controllers The inverter technology provides the best energy efficiency concerning the realization of variable flow systems: it is widely documented that the advantages resulting from the use of inverter are particularly marked in those plants in which the operating cycle is most varied. The use of the inverters also allows to exploit particularly large speed intervals and operation dynamics, to decrease motor’s stress reducing the negative effects caused by acceleration and deceleration transient, to implement protection functions to safeguard...

Open the catalog to page 5
SPEED CONTROLLERS wall mounted and built-in - 6

FE1018 - FE1019 motor control (3,5 A - 8 A) The FE1018 and FE1019 (in the picture, the 3,5 A model FE1018) are two models of single-phase frequency converters for the control of induction motors that respectively absorb up to 750 W (max current absorption of 3,5A) and 1500 W (max current absorption 8A) of electrical power. The front panel integrates the on/off switch and a rotary knob to vary continuously the motor’s speed: the microprocessor, which is the heart of the inverter, allows to manage appropriate acceleration and deceleration ramps and to realize protection techniques for...

Open the catalog to page 6
SPEED CONTROLLERS wall mounted and built-in - 8

ELECTRONIC REGULATORS (built-in)  Phase-cut technology DIGITAL FE1038 – 4 A: A practical solution that integrates power board and user interface into a single control unit for fast and easy panel mounting. Controls single-phase 4A induction motors (maximum current absorbed by the motor, 900W), lighting system and solenoid valve. FE1038 FRONT PANEL (optional) p/n FE1039 FEGR017- 4 A: It allows the control of 4A single-phase induction motors (max power absorption 900W), and of an external solenoid valve, the lights and a possible optional load at mains voltage. A 5 keys user interface, a LED...

Open the catalog to page 8
SPEED CONTROLLERS wall mounted and built-in - 10

• Electromechanical controllers for common wire motors Phase cut or electromechanical regulators that control the motor and, in some cases, an optional load. On request, we supply the regulators with cable glands and cables. FE1037 is a 3-speed electromechanical controller for common wire motors, for a maximum current absorption of 10A, already included with the cable glands. FE1040 is a 4-speed electromechanical controller for common wire motors, for a maximum current absorption of 10A, already included with the cable glands. • Auto-transformer for 2 wires single-phase induction motors <*...

Open the catalog to page 10
SPEED CONTROLLERS wall mounted and built-in - 11

CONTROLLERS FOR SUCTION HOODS COMBINED WITH OVENS AND DISHWASHERS WALL MOUNTED - FE230/U with humidity sensor FOR DISHWASHER Is a microprocessor-based system with low consumption when in stand-by. Allows you to control the hood motor in manual or automatic mode by means of probe measurements at the opening of the machine. FEGF01 – FEGR021 with temperature probe and microswitch FOR OVEN HOODS Allows you to control the hood motor in manual or automatic mode by means of probe measurements at the opening of the machine, or immediately at the oven door opening thanks to the microswitch (for the...

Open the catalog to page 11
SPEED CONTROLLERS wall mounted and built-in - 12

FASAR ELETTRONICA S.r.L. Strada della Marina 9/6 - 60019 Senigallia (AN) Italy T: 071.6609805 www.fasar.it - www.fasarelettronica.com commerciale@fasar.it

Open the catalog to page 12

All Fasar Elettronica S.r.l. catalogs and technical brochures