PCB Depaneling
4Pages

Fancort Depaneling Systems For Every Production Requirement. Low to Moderate Volume Model IUTG • Two circular knives separate panels up to 15" long • Manual or motorized models • Infinitely variable speed motor with reverse • Unique cutter design for cleaner cut and longer life • Positive locking guides prevent boards from walking See page 3 Model VPD3-1M • Manual round knife cutting against linear knife • Cuts board with components overhanging score line with modified linear knife • Wide table on both sides of knife, 6.25"x20" • Table sides can be raised or angled • Stops on top to set cut length, 18" max. • Custom model with cut length to 24" max. • Cut safely with components up to .030"-.040" from the score line • Easy adjustment on height of round knife High VolumeModel VPD5 Jfc • Linear knives shear with the pre-score • No stress to board or adjacent components * i - up to 0.5mm edge distance • Operator cannot miss insert PCB • Substantial clearance for high components X • Easy adjusting upper blade setting • Two models 10" or 13" capacity See page 4 Model VPD3-1 • Motorized version of VPD3-1M • Easily programmable cut length, up to 18" • Custom model with cut length to 24" max. • Foot switch operation with safety light curtain • Four fixed speeds Janome JR 2000 Series Routed Boards Low VolumeModel NTR-1 & NTR-2 1Single knife machine removes tabs 1Change knives in less than 3 minutes Foot switch and scrap tray 1Knives for round boards ■ NTR-1 cuts up to .093" thick PCB 1NTR-2 cuts up to .125" thick PCB see page 5 Model NTP-1 • Single knife machine cuts along board edge • Separates hard to reach tabs • Cuts board up to .080" thick • Two locating pins maintain board position • Rugged C frame design • Vertical cutting motion • No scrap See page 5 PP-4/8 Moderate Volume Model PS-MR-1 • Cut up to six tabs at once • Minimal stress to board or components Pneumatic operation knife adjustment VPDS High Volume Janome JR 2000 Series • High production on panels with curved boards or multiple angles • Programmable with teaching pendant; very easy to set-up & program • Powerful vacuum system leaves no chips or dust See page 6 PP Series • Four presses up to 80 tons and working area of 460 x 320mm • Sliding bottom die for easy loading and unloading • Cast iron frame for rigidity • Affordable, high quality tooling See page Fancort has your depaneling solution! Not just one or two models, but a complete line of machines for tab-routed and scored-boards to meet every production application and throughput requirement fancort industries, inc 31 Fairfield Place, West Caldwell, NJ. 07006 • 973/575-0610 • Fax 973/575-9234 • www.fancort.com

VPD3 Series for Scored Boards NTG-4A for Scored Boards Robust construction with all-steel frame Light curtain for safety Dual disk blade design with motorized upper blade Wide stainless steel table (6.25" x 20") on both sides of cutting blade prevents board wobble. Can be height adjusted or angled so finished boards can fall away- The manual VPD3-1M is activated when the operator pulls the circular blade housing across the board. Two moveable stops are used to set the precise cut length. The action is smooth and can be easily controlled by the operator for separating very dense or small...

Safely Depanel PCBs Without Stress — Even if Sensitive Components Are .5 mm from the Scoring Line. Low-Cost Benchtop Delivers Precision Cuts Virtually Burr-Free; Works on Crowded Boards. This low-cost pneumatically powered machine uses a single knife to safely fit the width of slots. Because of the cut without damaging the board or short bottom die, the machine can be nearby components. Its compact size safely used to cut PCBs with components or connection plugs crossing the slot (8 lbs.) permits the unit to be easily — an added advantage when carried to multiple work sites. depaneling...

PS-MR-1 for Tab-Routed Boards Programmable Routers for Dense, Small, Odd-Shaped or Stress-Susceptible Boards. ‘Smart Nibbler’ Snips up to 6 Tabs at a Time — Ideal for High-Volume Applications. JR .400 Three models available with work areas of up to 20" x 20" Stores 100 programs or 6,000 work points on resident memory card. Our aptly named “Smart Nibbler" makes fast work of separating routed slot panels. Employing up to six knives, the machine removes as many as six tabs simultaneously. The production sequence takes place with each of the blades adjusted in the longitudinal direction aligned...