Rest Pads & Gripper Pads Solid Carbide High impact carbide pads. Can be brazed or bonded into place. Carbide Tipped Constructed with a high impact carbide pad brazed to a heat treated alloy steel body. Mounts with tapped hole or a flat on the outside diameter for set screw mounting. Stainless Steel The pad is made from 17-4 stainless steel, hardened to Rc 43/46. Mounts with tapped or counter bored hole. Hardened Steel Made from 8620 steel, carburized and hardened to Rc 58/60 .050" case with black oxide finish. Mounts with tapped or counter bored hole. Abrasive Diamond Surface The abrasive surface is permanently fused to a 17-4 stainless steel pad, hardened to Rc 43/46. The surface texture is comparable to a 100 grit abrasive. Mounts with tapped or counter bored hole. Non-Marring Delrin Manufactured from white Delrin. Mounts with counter bored or tapped hole. Sof-Top™ Urethane Surface The urethane surface is permanently bonded to a 300 series stainless steel pad. The urethane provides excellent protection against damage on delicate work surfaces. They are available in three durometers. Tapped hole mounting. TOOTH PATTERN SPECIFICATIONS Throughout this catalog, you will find reference to tooth patterns on all serrated grippers. Please use the chart below for specific information regarding these tooth patterns. If additional information is required, please contact us. Angle Grippers Angular Straight Round and Square Grippers Diamond Serration Pattern Straight Serration Pattern “SS” Fixtureworks | 33792 Doreka Dr., Fraser MI 48026 | Phone: 586-294-1188 | Fax: 586-294-4843 | www.fixtureworks

Serrated Gripper Pads High Speed Tool Steel Round, square, edge, and angle grippers manufactured from M-2 high speed tool steel, hardened to Rc 60/62 with black oxide finish. Mounts with tapped hole, counter bored hole or a flat on the outside diameter for set screw mounting. Carbide Tipped Round, square, and angle grippers constructed with a high impact carbide pad brazed to a heat treated alloy steel body. Mounts with tapped hole or a flat on the outside diameter for set screw mounting. Solid Carbide Round and square grippers manufactured from high impact carbide in a solid gripper pad or as...

THREADED ADJUSTABLE GRIPPER OVERVIEW Carbide Tipped Round and Hex head styles constructed with a steel body. Carbide tipped for positive holding and wear resistance. High Speed Steel Manufactured from M-2 high speed tool steel, hardened to Rc 55/58. Internal hex on backside allows for positioning adjustment. AdjustaGripTM The gripper pad can be replaced when it becomes worn. Uses tapped through hole grippers. AccuGripTM Designed to fit within chuck jaws to adjust concentricity. Carbide tipped for wear resistance. SWIVOTS® & THRUST SCREW OVERVIEW Swivots® & Thrust Screw Replaceable Balls Sof-TopTM...

SWIVOTS® & THRUST SCREW OVERVIEW ■ Unique design allows the pad and ball cup to swivel, tilt, clamp, grip, hold position and secure a work piece. ■ The internal ball cup allows the pad to rotate 360 degrees and tilt at varying degrees from center. ■ Interchangeable parts speed setups and changeovers. ■ O-ring holds the ball in place and keeps out dirt and other contaminants. ■ Replaceable pad design allows for easy change out when the pad is worn or a different contact surface is required. ■ The unique design of the Swivots prevent the ball from exceeding the specified degree of swivel which...

SWIVOTS® - REPLACEABLE SWIVEL BALLSwivots® Replaceable Swivel Ball Style These Replaceable Ball Style Swivots® are found on the following pages.REPLACEABLE BALLS Serrated Flat Flat Tool Steel Delrin Tool Steel Sof-Top Cone Flat Cone Flat Cone AbrasiveUrethane Surface Delrin Stainless Diamond Cone VITON O-RING HOUSINGS Threaded Body Design Load Calculator To calculate the load on the contact surface, divide the torque applied (in/lbs) by a factor shown below. Assumes no lubrication threaded into steel. Use as a guideline only. Hex Head Design INCH ■ These Replaceable...

SWIVOTS® - REPLACEABLE SWIVEL PAD Swivots® Replaceable Swivel Pad Style These Replaceable Pad Style Swivots® are found on the following pages. REPLACEABLE PADS Sof-Top Cone Flat Flat Flat Flat Carbide Tipped STAINLESS BALL CUP LOCK SCREW VITON O-RING HOUSINGS Load Calculator To calculate the load on the contact surface, divide the torque applied (in/lbs) by a factor shown below. Assumes no lubrication threaded into steel. Use as a guideline only. To select the proper pad: 1. Determine the diameter of the pad for the housing assembly. This can be found on the following pages under "Replaceable Pad...

THRUST SCREW ASSEMBLIES Replaceable Ball Thrust Screw AssembliesThese Replaceable Ball Thrust Screw Assemblies are found on the following pages. REPLACEABLE BALLS Sof-Top Cone Flat ConeUrethane Surface DelrinStainless Flat Cone AbrasiveStainless Diamond ConeStainless Serrated Tool Steel Round Ball Stainless Round Ball Delrn o VITON O-RING HOUSINGS Tightening Torque Calculator To calculate the approximate tightening torque (in/lb) required to achieve a required force, multiply the force by the appropriate factor listed below. Assumes no lubrication threaded into steel. Use as a guideline...