fairlane_workholding
79Pages

QUICK INDEX TG GRIPSERTS GRIPPER SYSTEM Page Number Part # Prefix RUBBER GRIPPER PADS – GP SERIES Page Number Part # Prefix FIXED GRIPPERS Page Number Part # Prefix ROUND STYLE Fairlane Products | 33792 Doreka Dr., Fraser MI 48026 | Phone: 586-294-6100 | Fax: 586-294-6822 | www.fairlaneproducts.com

QUICK INDEX CARBIDE PADS Page Number Part # Prefix REST PADS Page Number Part # Prefix THREADED ADJUSTABLE GRIPPERS Page Number Part # Prefix SWIVOTS® – REPLACEABLE SWIVEL BALL STYLE Page Number Part # Prefix BASE DESIGN Fairlane Products | 33792 Doreka Dr., Fraser MI 48026 | Phone: 586-294-6100 | Fax: 586-294-6822 | www.fairlaneproducts.com

Part # Prefix SWIVOTS® – REPLACEABLE SWIVEL PAD STYLE Page Number Part # Prefix Page Number Part # Prefix Page Number Part # Prefix BASE DESIGN THREADED BODY THRUST SCREW ASSEMBLIES Page Number Part # Prefix THREADED BODY Fairlane Products | 33792 Doreka Dr., Fraser MI 48026 | Phone: 586-294-6100 | Fax: 586-294-6822 | www.fairlaneproducts.com

Rest Pads & Gripper Pads Solid Carbide High impact carbide pads. Can be brazed or bonded into place. Carbide Tipped Constructed with a high impact carbide pad brazed to a heat treated alloy steel body. Mounts with tapped hole or a flat on the outside diameter for set screw mounting. Hardened Steel Made from 8620 steel, carburized and hardened to Rc 58/60 .050" case with black oxide finish. Mounts with tapped or counter bored hole. Non-Marring Delrin Made from white Delrin. Mounts with tapped or counter bored hole. Stainless Steel The pad is made from 17-4 stainless steel, hardened to Rc...

High Speed Tool Steel Round, square, edge, and angle grippers manufactured from M-2 high speed tool steel, hardened to Rc 60/62 with black oxide finish. Mounts with tapped hole, counter bored hole or a flat on the outside diameter for set screw mounting. Carbide Tipped Round, square, and angle grippers constructed with a high impact carbide pad brazed to a heat treated alloy steel body. Mounts with tapped hole or a flat on the outside diameter for set screw mounting. Solid Carbide Round and square grippers manufactured from high impact carbide in a solid gripper pad or as a solid gripper...

THREADED ADJUSTABLE GRIPPER OVERVIEW Carbide Tipped Round and Hex head styles constructed with a steel body. Carbide tipped for positive holding and wear resistance. High Speed Steel Manufactured from M-2 high speed tool steel, hardened to Rc 55/58. Internal hex on backside allows for positioning adjustment. AdjustaGripTM The gripper pad can be replaced when it becomes worn. Uses tapped through hole grippers. AccuGripTM Designed to fit within chuck jaws to adjust concentricity. Carbide tipped for wear resistance. SWIVOTS® & THRUST SCREW OVERVIEW Swivots® & Thrust Screw Replaceable Balls...

SWIVOTS® & THRUST SCREW OVERVIEW ■ Unique design allows the pad and ball cup to swivel, tilt, clamp, grip, hold position and secure a work piece. ■ The internal ball cup allows the pad to rotate 360 degrees and tilt at varying degrees from center. ■ Interchangeable parts speed setups and changeovers. ■ O-ring holds the ball in place and keeps out dirt and other contaminants. ■ Replaceable pad design allows for easy change out when the pad is worn or a different contact surface is required. ■ The unique design of the Swivots prevent the ball from exceeding the specified degree of swivel...

TG GRIPSERTS GRIPPER SYSTEM Typical Clamping Min. Clamping With as little as 2mm (.08") of workpiece clamp surface to securely hold the Surface Surface workpiece, TG GripSert workholding grippers are ideal for 5-axis machining (Double Row) (Single Row) operations and minimizing scrap material. The GripSert grippers offer many 3.5mm (.14”) 2mm (.08”) advantages over traditional clamping systems including exceptional clamping stability, no need for pre-machining or dovetailing workpieces, vibration dampening and allowing for very secure holding at lower clamping forces to avoid deforming the...

TG GRIPSERTS GRIPPER SYSTEM Jaw Set I Retrofit Kurt 6" These jaw sets allows you to use TG GripSert inserts on Kurt 6" vises. Set includes one pair of jaws, Torx T9 wrench and 10-pack of screws. TGJ-06P also includes one pair of quick change 1.6-inch parallels. On TGJ-06P, install and uninstall the parallels easily by hand with no additional tools necessary. Part #DD1LL1L2WW1HH1 Parallel Height TGJ-0643.795.983.87.625.72531.74.93-TGJ-06P .43 .79 5.98 3.87 .625 .72 .53 1.74 .93 1.61 Parallel Pairs Parallel Height Part #Qtymm TG-PRL615/20/25/30/391/422 GripSert...

RUBBER GRIPPER PADS - GP SERIES Strips Hatch Surface Least surface contact; Increased surface pressure; forces applied over reduced contact area Fine Hatch Surface Medium surface contact; Medium surface pressure; forces applied over reduced contact area MODIFICATIONS AVAILABLE Smooth Surface Greatest surface contact; Gripping forces evenly distributed Rubber gripper pads are ideal for industrial grade contact wear points in automation and positioning applications. Black nitrile rubber (60A durometer) is molded to a malleable aluminum backing that can be formed to round or sharp corners. The...

FIXED GRIPPERS Fairlane Products | 33792 Doreka Dr., Fraser MI 48026 | Phone: 586-294-6100 | Fax: 586-294-6822 | www.fairlaneproducts.com 11

FIXED GRIPPERS

FIXED GRIPPERS Round Style I Carbide Tipped I Serrated I Tapped I Inch & Metric Constructed with a serrated carbide gripper pad brazed to a heat treated alloy steel body. Blind-hole tap for back side mounting. Flat on O.D. for set screw mounting. See page 4 for tooth pattern specifications. See page 5 for mounting specifications. INCH *Keyway= .130" width, .060" depth C B Flat Part #_Height Pos. Flat Pad Tooth Width Dia. Pattern INCH DIAMETERS WITH METRIC THREADS B Flat Flat Pad Tooth Part #Height Pos._WidthDia. Pattern Fairlane Products | 33792 Doreka Dr., Fraser MI 48026...