“SC” Series NEW PRODUCT BULLETIN Swing Clamp Cylinders featuring. . . • Magnetic Piston • Clamp arm with adjusting bolt • Four rod end flats for clamp arm positioning all included as standard at no extra charge! Specifications The clamp arm rotates 90° as it extends away from the workpiece providing clearance and access for unload/load operations. Double acting operation and standard magnetic piston offer positive cycles, durability and workpiece detection features. Extruded aluminum body mounts directly and rigidly to equipment surfaces in a minimum of space. Operation cycle: 1) Clamp arm extends (straight line) as it releases clamp load from workpiece. 2) Arm rotates 90° to full extend position. 3) When retracting, clamp arm swings 90°: Model Code R = clockwise direction, Model Code L = counterclockwise rotation. 4) With clamp arm in position over the workpiece, it follows a straight line path to apply clamping force. Action Double Acting, Magnetic Piston Bore Size (mm) 12 16 20 25 32 40 50 63 Max. Moment (ft-lbs*) 0.73 2.8 5.1 9.5 19.9 34.6 78.9 134.2 Swing Stroke (mm) 7.5 7.5 10 10 13 13 18 18 Straight Stroke (mm) 10, 20 20, 50 Direction of Swing R-Clockwise; L-Counter Clockwise Angle of Swing 90° ± 10° Theoretical Clamping Force (lbs) See chart on page 2 Operating Media Compressed Air or Petroleum Based Hydraulic Fluid Max. Operating Pressure 145 psi (10 bar) - See “Precautions” Piston Speed 50 to 100 mm/sec Temperature Range -10° to + 70°C (+14° to 158°F) Lubrication Air line lubrication recommended * Max. bending moment allowed when retracting Weights (lbs) Model Straight Stroke SC12 SC16 SC20 SC25 SC32 SC40 SC50 SC63 10 0.15 0.22 0.55 0.62 1.10 1.31 – – 20 0.19 0.27 0.64 0.71 1.16 1.41 2.42 3.35 50 – – – – – – 2.98 3.98 How to Order 1) Specify “SC” 2) Specify the bore 3) Specify the straight stroke 4) Specify direction of swing Bore (mm) Series Note: ø12, ø16, ø20 a) Please order sensors separately from page 4. ø25, ø32, ø40 b) Please order Flange Kits separately from page 3. ø50, ø63 c) Swing Clamp Arm, four Wrench Flats and Magnetic Piston are included as standard at no extra charge. Competition charges extra for these essential features! Straight Direction of Swing Ports Stroke (mm) when retracting Blank = NPT 10: ø12 - ø40 R - Clockwise P = BSP Taper 20: ø12 - ø63 L - Counter Clockwise 50: ø50, ø63 1) Vertical (rod up or rod down) applications only. 2) Swing portion of stroke is only to be used to align a clamp arm to the workpiece. Do not attempt to use the swing stroke to apply forces to the work piece. 3) Make certain the cylinder applies loads only in the straight portion of stroke, the loaded surface of SC50, 63 Dim. X the workpiece is perpendicular 200 200 SC32, 40 See Page 3 SC to the clamp cylinder axis and 50 ,6 that the workpiece will not move SC20, 25 3 100 100 SC16 SC to create a rotational force 80 32 80 ,4 when clamped. 4) Clamp Arm 0 60 60 SC 20 SC12 Attachments: When removing ,2 40 40 5 SC or attaching the clamp arm, 12 ,1 6 brace the arm with a wrench 20 20 or hold it steady in a vise. Not Allowable doing so may damage the Operating internal parts of the clamp cylinder. 5) Operating Pressure: Range Max. operating pressure should be determined based on Dim. “X of either standard or custom length clamp 145 87 29 20 40 60 80 100 200 58 116 14 arm. 6) Piston / Clamp Speed: Use flow control valves to Piston Speeds (mm/sec) Operating Pressure (psi) limit piston speed to not greater than limits shown. Specifications

“SC” Swing Clamp Cylinders FABCO-AIR • 3716 N.E. 49th Avenue • Gainesville, FL 32609 • Tel (352) 373-3578 • Fax (352) 375-8024 • E-Mail: [email protected] • Web Site: www.fabco-air.com Theoretical Output (lbs) Model Action Retract Extend Retract Extend Retract Extend Retract Extend Retract Extend Retract Extend Retract Extend Retract Extend Description Front end cover Rear end cover Housing Piston rod Piston Magnet Snap ring Snap ring Washer Bushing Fastening nut Positioning pin Material anodized aluminum alloy anodized aluminum alloy hard anodized aluminum alloy hard chrome plated carbon Steel...

“SC” Swing Clamp Cylinders FABCO-AIR • 3716 N.E. 49th Avenue • Gainesville, FL 32609 • Tel (352) 373-3578 • Fax (352) 375-8024 • E-Mail: [email protected] • Web Site: www.fabco-air.com P Port 2 Places NPT or BSP Taper See Page 1 “How to Order” X 8–ØO C'Bore 4–ØN Thru Hole F Swing Straight Stroke Stroke Total Stroke STANDARD FEATURES (for which the competition charges extra)!!! • Magnetic Piston • Clamp arm with adjusting clamp bolt • 4 rod end flats for clamp arm positioning Mounting Flange Mounting flange & fastener kit to provide alternative mounting and port orientation to a rectangular pattern....

FABCO-AIR • 3716 N.E. 49th Avenue • Gainesville, FL 32609 • Tel (352) 373-3578 • Fax (352) 375-8024 • E-Mail: [email protected] • Web Site: www.fabco-air.com Magnetically Actuated Sensors – Magnetic Piston is a standard feature of Fabco-Air swing clamp cylinders. When position sensing is desired for input to signal controllers, Fabco-Air sensors mount easily and securely inslots on the cylinder body. Round Profile Sensors feature surge suppression, polarity protection, LED indicator, and extremely fast switching speeds. They slide into mating 4mm keyhole slots on either side of the cylinder...