Universal Zone 1 Access Point Enclosure iWAP107
1 / 3Pages

iWAP107 Universal Zone 1 Access Point Enclosure Zone 1 Explosion Proof Wireless Access Point enclosure system with intrinsically safe RF outputs. Overview The iWAP107 is an ATEX and IECEx approved Zone 1 Access Point Enclosure with intrinsically safe RF outputs which is designed to allow the deployment of wireless networks in hazardous areas. The concept allows installation of equipment from leading WLAN vendors such as Cisco, Aruba, Aeroscout and Motorola. Each type of Access Point or RF transmitting device is rigorously checked and tested by Extronics to ensure conformity to the latest standards. This means that the user may select the vendor of their choice when extending a WLAN to hazardous areas. However equipment not previously approved will require assessment to determine its suitability. The galvanically isolated RF outputs of the iWAP107 allows users to choose non-certified antennas for use with their wireless hardware e.g. Extronics iANT2xx range of high quality rugged outdoor antennas. Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas. Up to eight antennas can be utilized, allowing the MIMO functionality of the latest 802.11n/ac compatible wireless access points to be implemented, providing optimum coverage and maximum data throughput on Chemical Plants, Oil Refineries or Oil & Gas Platforms. Optional features include surge arrestors for lightning suppression in outdoor installations and single mode or multimode fibre optic inputs to allow for extended Ethernet link distance. Features and Benefits Galvanically Isolated RF Outputs Non-certified antennas can be used with chosen wireless hardware* Extended Temperatures Operating temperature range of -20°C to +60°C for the most extreme environments. Future Proof Infrastructure As new hardware becomes available it can be assessed by Extronics for compliance to the certification. The existing hardware can then be replaced with the new version meaning the user is installing a future proof solution. Gigabit Ethernet Supports 100/1000Base-T/FX/LX options to offer a significant increase in speed over the older fast Ethernet standard. MIMO Radio Offers increased data throughput and higher immunity to signal interference for optimal performance in challenging industrial environments. Specification Certification Type Power Supply Maximum Power Consumption Basic configuration: 25W With heaters: 125W Enclosure Material Marine grade copper free aluminium light alloy, epoxy powder coated or 316L Stainless Steel (optional) Ingress Protection Aluminium—Approx 30kg (hardware dependant) 316L Stainless Steel—Approx 70kg (hardware dependant) Aluminium— 415 x 315 x 250 mm (w x h x d) 316L Stainless Steel— 415 x 315 x 253 mm (w x h x d) Ambient temperature: -20ºC to +60ºC (dependant on wireless hardware—see individual AP operating temperatures overleaf) Relative humidity; 0 to 95%, non condensing Input Connections - AC / DC power input screw terminals - 10/100/1000Base-T Ethernet on RJ45 socket - Single or Multi mode fibre input on LC connector & Splice Tray (all via M20x1.5-6H drilled entries) Ethernet Link distance 10/100/1000BASE-T Ethernet on CAT5e: up to 100m 100BASE-FX Multi Mode fibre : up to 2km, wavelength 1310nm 100BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm 1000BASE-LX Multi Mode fibre : up to 550m, wavelength 1310nm 1000BASE-LX10 Single mode fibre: up to 10km, wavelength 1310nm Output Connection Up to eight galvanically isolated N-Type RF outputs Internal RF Losses (typical) *Any antennas not listed in the Extronics range must be assessed by the user to ensure they meet the requirements for installation of non-electrical equipment in hazardous areas. Without Surge Arrestor: With Surge Arrestor: ATEX: TRAC14ATEX0022X IECEx: TRC 14.0010X NEC 500 - C1 D1: Pending Copyright © Extronics Ltd 2014. The information contained in this document is subject to change without notice. Extronics cannot be held responsible for any errors or inaccuracies within this document. Extronics Ltd., 1 Dalton Way, Midpoint 18, Middlewich, Cheshire, UK. CW10 0HU

Antenna Locations In order that customers enjoy the best possible wireless performance from their iWAP107 system we recommend that, where possible, antennas are remotely mounted as high as possible and with sufficient separation. It is recognised that in some instances remote mounting of antennas is not a feasible option and for these circumstances we have optimised the antenna positions for the various configurations. When completing the order information for option [#10] overleaf, you must specify remote or direct mounted antennas. The RF connections will then be supplied as shown in the...

iWAP107 - Universal Access Point Enclosure Specify option [#1] - Wireless Network Hardware Hardware supplied by customer* Hardware supplied by Extronics *Extronics can supply the wireless hardware, or alternatively you may wish to “free issue” one of the already certified solutions so that we can factory fit it (see option #2 for certified hardware list). (“Free Issue” means to supply and deliver to Extronics HQ at your own cost.) Specify option [#2] - Type Of Wireless Network Hardware (Max operating temperature listed in brackets only applies to PoE powered units, take lower value if...