Catalogs >
EXFO >
IQS/FLS-2600B

IQS/FLS-2600B
7Pages

Catalog excerpts

TUNABLE LASER SOURCE Continuous and precise tuning over the C and L bands. Inherent coherence control PLATFORM COMPATIBILITY Integrated Qualification System Next-Gen Networks

Open the catalog to page 1

IQS-FLS-2600B Tunable Laser Source HIGH-PERFORMANCE TUNABLE LASER SOURCE On the production floor, time is money. You need fast, cost-effective test instruments that maximize your production throughput. The IQS-2600B and FLS-2600B Tunable Laser Sources are ideal for complete characterization of fiber-optic filters, multiplexers and other dense WDM components. They are the logical choice for instrumentation calibration and for measuring wavelength-dependent gain, noise contribution and the saturation properties of EDFAs. › Ideal for complete characterization (IL, ORL and PDL) of DWDM passive...

Open the catalog to page 2

IQS-FLS-2600B Tunable Laser Source Scan of 2600B signal with an OSA 0 Low Spontaneous Noise Emission When combined with the source’s coherence properties, they are the best tunable lasers on the market for characterizing passive DWDM components. Over the 1515 nm to 1610 nm range, the IQS-2600B and FLS-2600B provide more than 75 dB local noise suppression and more than 45 dB in signal-to-total-noise ratio, making them ideal for testing both stopband (notch) and passband filters. Low ASE noise enables accurate isolation of DWDM components. Fast GPIB and Wavelength Tuning Maximize your...

Open the catalog to page 3

IQS-FLS-2600B Tunable Laser Source HIGH-END PERFORMANCE Natural Coherence Control Are you looking for a product to solve your problems with coherence control and longitudinal mode hopping? This tunable laser source is the answer. Its linewidth is made up of several simultaneously present longitudinal modes (FWHM of less than 1.5 GHz at 1580 nm). The narrow, multimode structure creates high-frequency mode competition (>10 MHz), which is well above the measurement bandwidth required in most passive component characterization setups. Mode-hop related problems are completely eliminated. The...

Open the catalog to page 4

IQS-FLS-2600B Tunable Laser Source APPLICATIONS Spectral Insertion Loss of Passive Components The stand-alone, GPIB-controlled FLS-2600B Tunable Laser Source and dual-channel PM-1600 High-Speed Power Meter provide a straightforward solution to quality control testing of three-port WDMs. Attain high measurement confidence due to insertion loss measurement at any number of wavelengths. Dual-channel PM-1600 High-Speed Power Meter drop pass FLS-2600B Tunable Laser Source Filter Alignment Station OUTPUT Combine the IQS-2600B Tunable Laser Source with the IQS-1600 High-Speed Power Meter to...

Open the catalog to page 5

IQS-FLS-2600B Tunable Laser Source SPECIFICATIONS a Wavelength Range (nm) Effective spectral linewidth FWHM (GHz) Maximum Minimum Power Output power g, h (dBm) Repeatability for a wavelength change c (dB) Signal to SSE (dB) ±1 nm from peak with RBW 0.1 nm Internal Variable Attenuator Attenuation range (dB) Linearity with attenuation (dB) Repeatability for specific wavelength c (dB) Notes a. Specifications are valid at 23 °C ± 1 °C after one-hour warmup time. b. FWHM: full width at half maximum. The specification is valid at 1580 nm, where it corresponds to 12 pm. Given in HR mode. Typical...

Open the catalog to page 6

IQS-FLS-2600B Tunable Laser Source GENERAL SPECIFICATIONS Output fiber type Operating temperature Storage temperature Instruments Drivers LabVIEW™ drivers and SCPI commands Remote Control With FLS-2600B: GPIB (IEEE-488.1, IEEE-488.2) and RS-232. With IQS-500 or IQS-600: GPIB (IEEE-488.1, IEEE-488.2), Ethernet and RS-232. Standard Accessories User Guide, Certificate of Compliance and AC power cord SAFETY Class 1 LASER PRODUCT 21 CFR 1040.10 and IEC 60825-1:2007 ORDERING INFORMATION FLS-2600B-XX-XX IQS-2600B-XX-XX For the IQS-500 or IQS-600 system Connector Mode EI-EUI-28 = UPC/DIN 47256...

Open the catalog to page 7