pco.dicam C1 LT
15Pages

dicam C1 LT intensified 16 bit sCMOS camera intensified sCMOS technology 1504 x 1504 pixel 10G fiber optic data interface exposure time 51 ns with 18 mm intensifier double image mode with 300 ns interframing time

As an expansion to our well established pco.dicam C1 family, we are now adding the pco.dicam C1 LT model, which is based on 18 mm image intensifies. For applications which do not challenge the absolute technical limits in intensified imaging, the new pco.dicam C1 LT is a budget friendly alternative to the high end versions pco.dicam C1 and pco.dicam C1 UHS. Building on the proven technology of our established hardware platform the pco. dicam C1 LT gives you full access to the world of true optical gated imaging. Its S20 photo cathode matches most application requirements. Adapted from the...

camera components overview image intensifier optical coupling lens system sCMOS image sensor camera system 10G fiber optic based interface phosphor screen input window subject to changes without prior notice | lens is sold seperately ©PCO AG, Kelheim | pco.dicam C1 LT data sheet | v1.00

pco .dicam C1 LT technical specifications »image intensifier type HighRes micro channel plate (MCP) 6 pm channel input window synthetic silica image intensifier pitch distance 6 pm image intensifier MCP type single stage low resistance MCP for high strip current MCP operational modes continuous gated for enhanced extinction ratio image intensifier diameter 18 mm phosphor screen material P43, P46 output window glass image intensifier system > 50 lp/mm @ 5 % MTF typical (depends on phosphor) shortest gating time 51 ns Typical transmittance of image intensifier input window materials. data...

» photocathode quantum efficiency Spectral sensitivities of different photocathode material: S20 (multialkali) data courtesy of Hamamatsu Photonics photocathode material data courtesy of Hamamatsu Photonics You can combine all photocathode materials with P43 or P46 phosphor. Whereas the P43 phosphor has a much brighter emission than the P46 phosphor, it has a rather long decay time, i.e. the time required until the phosphor emission fades out after the excitation by electron bombardement has been stopped. This decay time is therefore critical for fast image repetition rates, primarily in...

technical specifications ■■■ Km » optical coupling lens system “ultra-speed tandem lens” between image intensifier & sCMOS transmission efficiency > 30 % scaling rates 6=0.53 for 18 mm intensifier The projected image circle is completely covered by 1504 x 1504 6.5 pm pixels of the sCMOS detector. There is no “waste“ of valuable intensifier area. As a consequence, the four corners of the sCMOS sensor remain black. subject to changes without prior notice | lens is sold seperately ©PCO AG, Kelheim | pco.dicam C1 LT data sheet | v1.00

dicam C1 LT 3 technical specifications sCMOS image sensor type of sensor scientific CMOS (sCMOS) sensor format / diagonal shutter mode single image double image 76.9 lp/mm (theoretical) spectral range 15,000 e- for P46 phosphor 30,000 e- for P43 phosphor 1.1 med / 1.5 rms e- single image 2.2 med / 2.5 rms e- double image 13,600 : 1 (82.7 dB) for P46 phosphor 27,200 : 1 (88.7 dB) for P43 phosphor 58 % for P43 peak emission @ 545 nm 57 % for P46 peak emission @ 530 nm 300 nm ... 1000 nm anti blooming factor fullwell capacity readout noise2 dynamic range quantum efficiency 1 Modulation...

perfect fit: phosphor emission vs. sCMOS quantum efficiency 100 relative phosphor emission intensity quantum efficiency quantum efficiency [ % ] [% ] QE sCMOS image sensor This chart describes the spectral situation for the internal imaging of the image intensifier`s phosphor output screen to the sCMOS sensor of the camera detector module. This imaging is done by the highly efficient tandem lens system. Please note: The spectral sensitivity relevant for your experiment is solely determined by the QE curve of the photocathode material of the image intensifier (page 5). subject to changes...

» camera system frame rate 120 fps @ 1504 x 1504 pixel pixel scan rate binning horizontal binning vertical horizontal: steps of 4 pixels vertical: steps of 1 pixel cooling method + 7 °C stabilized, 1 stage peltier with forced air (fan) input signals optical trigger (FOL), electrical trigger, arm input (TTL level, BNC connectors), gate disable (high-speed TTL input, BNC connectors) output signals gate/expos out monitor, user monitor output (TTL level, BNC connectors) time stamp in image (1 ps resolution) » exposure modes single image mode exposure times variable 51 ns ... 250 ns (1 ns...

pco .dicam C1 LT » general camera system power supply 18 ... 28 VDC operating humidity range 10 % ... 80 % (non-condensing) storage temperature range - 10 °C ... + 60 °C optical mount F-mount optional: C-mount vacuum mount (optional) sealed camera front attaches to vacuum equipment lens remote controller electronic control for Canon EF lenses maximum cable length 10 km (CLHS FOL) subject to changes without prior notice | lens is sold seperately ©PCO AG, Kelheim | pco.dicam C1 LT data sheet | v1.00

technical specifications » camera interface data transfer Camera Link HS, FOL cable, frame grabber _(Single F2,1X1, S10)_ maximum cable length 10 km (CLHS FOL) input signals optical trigger (FOL), electrical trigger, arm input (TTL level, BNC connectors), gate disable (high-speed TTL input, BNC connectors) output signals gate/expos out monitor, user monitor output (TTL level, BNC connectors) 1511 tews pco subject to changes without prior notice | lens is sold seperately ©PCO AG, Kelheim | pco.dicam C1 LT data sheet | v1.00

technical specifications dimensions F-mount and C-mount lens changeable adapter. All dimensions are given in millimeter. camera view subject to changes without prior notice | lens is sold seperately ©PCO AG, Kelheim | pco.dicam C1 LT data sheet | v1.00