Linear actuator CAMT Play–free motion Easy installation Compact design Standards IEC/UL 60601-1 (Edition 3.1) IEC/UL 60601-1-2 (Edition 4)

CAMTLinear actuator for surgical tables and procedure chairs Benefits • Play-free motion • Easy installation • Compact design Standards • IEC/UL 60601-1 (Edition 3.1) • IEC/UL 60601-1-2 (Edition 4) Rated push load Rated pull load Static load (push/pull) 1) Safety factor on rated load 2) 3) Speed (full load to no load) 4) Stroke Voltage Current consumption Duty cycle Ambient temperature IP protection Noise level (max) 1) Compliant with static load according to IEC/UL 60601-2-46 2) Static safety factor to prevent mechanical hazards according to IEC/UL 60601-1 3) Depending on stroke and attachment...

Product benefits Play–free motion – Extra patient comfort Smooth movement thanks to the play-free components. Fig. 1 Front attachment: play-free Unlike common actuators that shake when the load direction changes, CAMT keeps the movement smooth throughout the whole process (⮑ diagram 1). Easy installation – Simplicity It is easy to install thanks to the new design with extra front and rear attachment with 1 or 2 degrees of freedom (DOF) in motion (⮑ fig. 1 and 2). Compact design – Excellent system integration The compact design enables a excellent system integration. It can be installed as a single...

Dimensional drawing Clevis attachment (CAMT20-xxxxx-00L-AA-AFx-000) S±2 (Stroke) Retracted length: L = Stroke (S) + Offset (X) + 104 * Standard Offset = 36 Long protection tube Short protection tube Retracted length: L = Stroke (S) + Offset (X) + 50 (long protection tube) L = Offset (X) + 150 (short protection tube) * Standard Off

Retracted length: Long protection tube L = Stroke (S) + Offset (X) + 50 (long protection tube) L = Offset (X) + 150 (short protection tube) * Standard Offset = 60 Short protection tube Motion angles of play for front and rear attachments +50° -90°

Performance diagrams Speed-load diagram Current-load diagram Safety factor load conditions Push load reduction for static safety factor, S=4 (IEC/UL 60601-1) Safe push and pull load for static safety factor, S=2.2 (IEC/UL 60601-2-46) Clevis attachment 1 DOF attachment, with long protection tube 2 DOF attachment, with long protection tube Valid for all CAMT configurations

Linear actuator EWELLIXRear attachment orientation Standard bracket (1 DOF and 2 DOF) Suitable control units and accessories Control units U-bracket (1 DOF)Connecting diagram 24 V DC Hand switch Foot switch Desk switch Plug P1: DIN-8 connector Flying leads Plug P2: Molex Mini-fit Jr. 6-pole Plug P1 Wire color Section Function Plug P2 6 Yellow AWG 24 hall sensor 1 signal 3 8 Green AWG 24 hall sensor 2 signal 6

Distance between front pivot and gear box (Offset "X", see dimensional drawing) Protection tube length Short (shortest possible length) 0 0 S Long (lead screw covered when retracted) 0 0 L Front attachment — Rod clevis D12 H7 bore 1 DOF attachment 2 DOF attachment Rod with D8 H7 bore Rear attachment Rear clevis D20 H7 bore 0° (only with long protection tube) A 2 DOF attachment 0° Rear clevis D20 H7 90° (only with long protection tube) 1 DOF attachment 180° 1 DOF U-bracket attachment 0° 1 DOF U-bracket attachment 90° 1 DOF U-bracket attachment 180° 2 DOF attachment 180° Mechanical options Backup...

© Ewellix All contents of this publication are the property of Ewellix, and may not be reproduced or given to third parties (even extracts) without permission. Although great care has been taken in the production of this catalog, Ewellix does not take any responsibility for damage or other loss resulting from omissions or typographical errors. The photo may differ slightly in appearance from the actual product. Due to continuous improvements being made in our products, the product’s appearance and specifications are subject to change without notice. PUB IL-07014-EN-October 2019 Certain image(s)...