Catalogs >
Evident - Olympus Scientific Solutions >
DC1–DC5

DC1–DC5
5Pages

Catalog excerpts

DC1–DC5 Dual Element Corrosion Transducers A Complete Corrosion Monitoring Toolbox for Pipeline and Tank Integrity Preventative oil & gas pipeline and tank maintenance helps keep people safe and enables the flow of raw materials. As a leading NDT equipment manufacturer, our DC series (DC1–DC5) dual element transducers provide inspectors with a complete corrosion monitoring toolbox to support pipeline and tank inspection. These versatile, compact transducers are optimized for corrosion and thin materials and work with a wide variety of NDT instruments and ultrasonic inspection procedures. All models provide a cleaner signal than single element transducers and offer less ring down than comparable models— helpful for resolving smaller defects, inspecting close to the surface, and differentiating between two indications. DC1 and DC2 Transducers: Tough and Versatile With a 7.5 MHz frequency and slight roof angle, DC1 and DC2 dual element transducers provide optimal nearsurface resolution in the range of 0.030–2 in. (0.76–50.8 mm) in steel. Key Benefits: • Ideal for coverage of thin materials • xcels at thickness measurement, corrosion mapping, and E flaw sizing • ated for elevated temperature pipe and tank inspections R with a heat-resistant delay line up to 150 °C (300 °F) • vailable in standard (DC1) and thick-walled (DC2) housings A • its into small spaces: low profile (18 mm high) and 0.455 in. F (DC1)/0.56 in. tip diameter (DC2) • uilt to last even with frequent scrubbing due to thick-walled, B wear-resistant housing (DC2) • Knurled case is easy to grip • Broad compatibility with unmolded BNC or LEMO connectors • Effective on pipes as small as 1 in. (25.4 mm) OD • Improved spring strain relief (BNC connector o

Open the catalog to page 1

Nominal wall thickness: 0.325 in. (8.255 mm)—No corrosion Remaining wall thickness: 0.251 in. (6.375 mm)—Corrosion DC3–DC5 Transducers: Inspect Thinner Materials and Go Beyond Corrosion Monitoring The DC3, DC4, and DC5 dual element transducers expand your inspection capabilities. Thanks to 5 MHz frequencies and optimal element sizes/placement, inspectors can monitor corrosion of thinner material. The DC3 model with its high-angle design takes the series beyond corrosion monitoring and thickness measurement to include thin-wall pipe weld inspection and other applications, with a useful depth...

Open the catalog to page 2

DC4 and DC5 Transducers: Optimized to Detect Flaws and Measure Thickness in Thin Materials Manufactured at 5 MHz with slightly angled elements and a 0-degree longitudinal wave, the DC4 and DC5 dual element transducers offer enhanced thickness measurement and flaw detection in thin materials ranging from 0.040–1.5 in. (1.02–38.1 mm). Key Benefits: • Optimal near-surface resolution for thin materials • light roof angle improves flaw detection and thickness S measurement • eplaceable wedges lengthen the transducer’s R useful life • coustic noise barrier for pitch-catch technology A prevents...

Open the catalog to page 3

Depending on your application, any one or a combination of these five transducers offers improved corrosion monitoring and defect sizing. As field inspections change, you can benefit from having the complete set with a total combined thickness range of 0-2 in. (0-50.8 mm), as well as an extra pipe weld inspection tool (DC3 model). Transducers are available to purchase separately or, for added convenience, as a toolbox kit with the complete DC1-DC5 transducer lineup. For available kit options, see the images and part numbers below. Compatible to instruments with Female BNC and or Female LEMO...

Open the catalog to page 4

Pairing with the EPOCH™ 650 or 6LT flaw detectors or the 38DL PLUS™ thickness gauge* enables accurate, efficient corrosion mapping for evaluation of nominal wall thickness, pitting, and flaw type/size. DC1-DC5 Transducer Specifications and Dimensionswww.olympus-ims.com OLYMPUS SCIENTIFIC SOLUTIONS AMERICAS is certified to ISO 9001, ISO 14001, and OHSAS 18001. *All specifications are subject to change without notice. All brands are trademarks or registered trademarks of their respective owners and third party entities. Olympus, the Olympus logo, EPOCH, and 38DL PLUS are trademarks of Olympus...

Open the catalog to page 5

DC1–DC5 5Pages

Catalog excerpts

All Evident - Olympus Scientific Solutions catalogs and technical brochures

DC1–DC5
5Pages