ETP-EXPRESS - 4 Pages

Add to MyDirectIndustry favorites
ETP-EXPRESS

Catalog excerpts

Corrosion resistant and easy to clean The demand from the food and process industries is increasing for stainless steel hub-shaft connections. The most common sizes of the hydraulic connection ETP-EXPRESS are available in stainless steel. The flat flange design allows for easy cleaning, essential within food processing. Also the pressure medium and screw lubricant are approved for use in the food industry.

 Open the catalog to page 1

Small built-in dimensions and one radial screw In this cleaning system for workpieces in the automobile industry, ETP-EXPRESS R is used for fastening of the brushes. The minimal built-in dimensions, radial tightening, good runout (less vibrations), moderate surface pressure with thin hubs (a bearing outside the hub) and resistance to fretting corrosion were important factors. Also the quick change of brushes was a benefit. Food approved A through going shaft in a gearbox is locked in both ends with ETP-EXPRESS R. The gearbox drives a mixer for food. Also the pump wheel in the mixer is...

 Open the catalog to page 2

ETP-EXPRESS R is available as standard for shafts 15-80 mm, also imperial. Runout ≤ 0,02 mm. Number of mountings 200 – 800 (size dependent). The extremely thin built-in dimensions allows for a compact design with low weight and inertia. Construction ETP-EXPRESS R is a hydraulic connection which consists of a double-walled hardened stainless steel sleeve filled with a pressure medium, and a flange. The flange part contains a stainless screw and piston with seals to maintain pressure. Benefits and features • ETP-EXPRESS R have the same benefits and features as ETP-EXPRESS. • All parts exposed...

 Open the catalog to page 3

Technical specification ETP-EXPRESS® R ETP-EXPRESS® Dimensions Transmittable axial radial torque force force T= Transmittable to^e when am! force is 0. } when the screw is tightened to Tt FA=Transmittable axial force when torque is 0. i FR=Max transmittable radial force at continuous operation. Max allowed bending torque: 5% of transmittable torque T. Tt= Recommended tightening torque for the screw. Further tightening does not increase the pressure. *) D2 is valid before mounting. Dimensions subject to alterations without notice. Tolerances    Type of torque Shaft h8 ( R-.5 only h7)....

 Open the catalog to page 4

All ETP catalogs and technical brochures

  1. Woodworking

    16 Pages

  2. ETP Metalworking

    52 Pages

  3. ETP ECOGRIP ER

    4 Pages

  4. ETP-OCTOPLUS

    4 Pages

  5. ETP-HYLOC

    4 Pages

  6. ETP-MINI

    2 Pages

  7. ETP-CLASSIC

    4 Pages

  8. HYDRO-GRIP-G2

    1 Pages

  9. Woodworking

    45 Pages

  10. HYDRO-GRIP-GE2

    1 Pages

  11. SPACERS-NIPPLES

    1 Pages

  12. PUMP-M08

    1 Pages

  13. HYDRO-GRIP-CIA

    4 Pages

  14. Blasolube 301

    7 Pages

  15. ETP-CUBIT-MINI

    2 Pages

  16. ETP-CUBIT

    11 Pages

  17. HYDRO-GRIP-GEW2

    1 Pages

  18. HYDRO-GRIP-G3

    1 Pages

  19. HYDRO-GRIP-AEI

    3 Pages

  20. ETP-HYDROPRESS

    1 Pages

  21. ETP-UNIGRIP

    2 Pages

  22. ETP-HYCON

    4 Pages

  23. ETP-OCTOPUS

    4 Pages

  24. HYDRO-GRIP-EI

    4 Pages

  25. HYDRO-GRIP-D-DI

    2 Pages

  26. HYDRO-GRIP-AH

    1 Pages

  27. HYDRO-GRIP-A

    1 Pages

  28. HYDRO-GRIP-AI

    1 Pages

  29. HYDRO-GRIP-B

    2 Pages

  30. HYDRO-GRIP-C

    1 Pages

  31. HYDRO-GRIP-BI

    1 Pages

  32. ETP-HYLOC

    4 Pages

  33. ETP-MINI

    2 Pages

  34. ETP-TECHNO

    4 Pages

  35. ETP-CLASSIC

    4 Pages

  36. ETP-EXPRESS

    5 Pages

Archived catalogs

  1. ETP HYDRO-GRIP

    4 Pages

  2. ETP ECOGRIP

    2 Pages