Residual current Build-in switch, Build-in devices circuit breakers with Control equipment RF Control Wireless System integral overcurrent protection DIFO Motor contactors Motor protective circuit breakers installation into distribution boards Low breaking capacity MCCBs, Low voltage MCCBs and low voltage switch disconnectors case circuit breakers with residual current protection Load Break Change Over Switch LBS..CO Change Over Fuse Load Break Switch FLBS Load Break Switch MLBS..CO Single phase safety Surge arresters group Surge arresters group Surge arrester ETITEC Fuse disconnectors Fuse disconnectors cylindrical fuse-links knife-blade fuse-links Fuse bases Strip type Disconnectors with Metal enclosures Free-standing cable Section rails fork, pin and SKN Din rail distribution blocks distribution cabinets Building, Industry and Energy Catalogue ULTRA QUICK Fuses for semiconductor devices protection Ultra Quick Catalogue GREEN PROTECT Protection of Photovoltaic Systems and other renewable energy sources Green Protect Catalogue

ITALWEBER Slovenia^™] Sn.ty. I™bI |ETI*ROMANiA' Ell d.o.o. ^ 1 PARENT COMPANY ETI d.d. Obrezija 5, 1411 Izlake, Slovenia Phone: +386 3 5657 570 E-mail: [email protected] http://www.etigrorp.eu http://www.eti.si ASSOCIATED COMPANIES ITALWEBER S.p.A. Via Risorgimento 84, 20017 Rho, Milano, Italy Phone: +39 02 939 771 E-mail: [email protected] http://www.italweber.it SUBSIDIARIES ETI Proplast d.o.o. Obrezija 5, 1411 Izlake, Slovenia Phone: +386 3 56 57 590 E-mail: [email protected] http://www.etiproplast.si ETI DE GmbH Dorfwiesenweg 13, 63828 Kleinkahl, Germany Phone: +49 6024 6397-0 E-mail:...

SOLID GSX METAL ENCLOSURES TYPE GT (IP65) INTERNAL STRUCTURAL SYSTEM AND ACCESSORIES METAL ENCLOSURES WALL - MOUNTED TYPE 4XN160 (IP 41, 42, 44) AND FLUSH - MOUNTED TYPE 4XP160 (IP 42, 44) METAL ENCLOSURES SYSTEM - SAFETY CLASS I Power needs control

A two-digit number established by the International Electro Technical Commission, is used to provide an Ingress Protection rating to a piece of electronic equipment or to an enclosure for electronic equipment. The protection class after EN60529 are indicated by short symbols that consist of the two code letters IP and a code numeral for the amount of the protection. Example: IP65 (NEMA 4) The two digits represent different forms of environmental influence: • The first digit represents protection against ingress of solid objects. • The second digit represents protection against ingress of liquids. The...

Metal enclosures/hermetic Application: GT-type metal enclosures cover a wide range of applications both for industrial and civil buildings. Due to its design they provide excellent air tightness, mechanical strength and functionality. They are used in places where electrical equipment is exposed to adverse effect of factors such as water, dust, mechanical impact. Features: ^ The door opening in the external enclosure contour, which allows direct connection in series of several enclosures (special designe of hinges) ^ High quality of polyurethane gasket - by using the newest technology in pouring...

Metal enclosures/hermetic Features and technical characteristics: Polyester powder paint RAL 7035 for external applications. * Specially profiled edges of the housing ensure stifness and exact protection against water. Poured polyurethane gasket on the door providing IP65 protection. Enclosures made of high quality sheet steel thickness from 1.2 mm to 2 mm. Resistant to external mechanical impacts - IK10. Cable flanges with curved edges to stiffen and poured gasket provides excellent cover. Door opening angle up to 120 degrees. The door opening in the external enclosure contour, which allows...

Metal enclosures/hermetic Door closing depending on the dimensions of enclosures: 2 locks for heights of 500 mm and more. Door closing depending on the dimensions of enclosures: 3-points closure for heights of 1000 mm and more. The doors in enclosures for heights of 400 mm and more, are equipped with vertical reinforcements with mounting holes spaced 25 mm. The doors in enclosures for heights of 400 mm and more are equipped with horizontal reinforcements with mounting holes spaced 25 mm. Solid construction of 3-point fasteners. Enclosures for heights of 800 mm and more are equipped with three...

Metal enclosures with mounting plate Symbols: Width * GT 100-80-30 / V Height Depth etibox Enclosures GT with mounting platel Note: The other parameters are on the next page.

Metal enclosures witn mounting plates Enclosures GT with mounting plate Cable entry width A1 (mm) Cover cable entry Cover cable entry depth width B A (mm) (mm) Mouting plate load (kg) Max. allowed power losses when max. number of devices are installed (W) Cable entry depth B1 (mm)

Metal enclosures with mounting plate etibox Accessories for hermetic enclosures (IP65) with mounting plate - lock for 3-points fastening for enclosures height >1000 mm - standard equipment for enclosures height < 800 mm

Metal enclosures with mounting plates

Dimensions of the body of enclosure GT

Metal enclosures witn mounting plates Dimensions of holder, mounting plates, holes for locks Mouting plates Holes in the door for locks Anchorage place The hole for 1 - point lock (for enclosures height ≤ 800 mm) The hole for 3 - points lock (for enclosures height ≥1000 mm)

Flush and wall-mounted enclosures, safety class I METAL ENCLOSURES WALL - MOUNTED TYPE 4XN160 (IP 41, 42, 44) AND FLUSH - MOUNTED TYPE 4XP160 (IP 42, 44) etibox Advantages: ^ High versatility and flexibility ^ Removable mounting framework (can be wired in the workshop or on the site) ^ Easy vertical dividing of enclosure by using special separating elements EPW ^ Covers and mounting plates are dedicated for ETI devices (MCCB's, MCB's, RCBO's disconnectors, etc.) ^ Short assembling time ^ Demountable back plate in wall-mounted version ^ Demountable door frame in flush-mounted version ^ Two door...

Flush and wall-mounted enclosures, safety class I The advantages and technical characteristics The wall-mounted enclosures consists of body with demountable back plates and non-perforated doors. The flush-mounted enclosures consist of a cassette and demountable frame with non-perforated doors. Wall-mounted enclosure set is equipped with: Flush-mounted enclosure is equipped with: • plugs of holes for wall-mounting • earthing set - nuts, washers, labels • screws AS-SH 6x10 for fixing vertical brackets WP-A and WP-U • cable membrane flanges – top • plugs of flangle holes – bottom • doors with lock...