eOne MF
2Pages

{{requestButtons}}

Catalog excerpts

eOne MF - 1

The new range of Etatron DS Dosing Pumps, the eOne series, represents an important step forward. The eOne technical characteristics deliver a reliable and effective solution for those businesses and customers involved in Chemical Dosing and W Treatment. The main common characteristics for all the eOne series (except for the eOne BASIC pump) are as follows: 1. High stroke rate up to 300 impulses/min 2. Flow rate variation control in relation to pressure changes 3. Energy efficient (typically 26W at the maximum load) using absorbed power control in comparison to the real dosing condit This gives the following advantages: • Constant dosing • Energy saving • Low operating temperatures resul in reduced mechanical/electrical stress and giving increased equipment life cycle and reliability. 4. eOne Dosing Pumps power supply range of 100v….250Vac (50-60Hz) voltage 5. Proportional function. 1÷1 on all manual pumps 6. UNDERLOAD – Suction alarm: in the event of low chemical level, blocked suction valve or damaged suction line 7. OVERLOAD – Discharge alarm: in the event of over pressure in pump head caused by an obstruction or increased operating system pressure beyond the pump specification - 8. Level control. Multifunction microprocessor dosing pump, suitable for applications which require proportional dosing. The pump operates at high dosing frequency (up to 300 impulses/min) and is equipped with backlit graphic display for correct setting of the various programming parameters. The functions performed by the pump are as follows: • Calibration procedure of the actual im injection rate delivered to a specified need • Manual flow rate regulation 0..100 %, 0..300 impulses/min • Proportio mode 1 x n (pulse multiplier), at each signal from the pulse supply emitting meter corresponds “n” injections of t pump, during the injections any following pulses neglected • Proportional mode 1 x n(M) (pulse multiplier with memory), each signal from the pulse supply emitting meter corresponds “n” injections of the pump, during the injections th following pulses from the meter are memorized and the pump modifies “n” (injections to be delivered) in proport to the pulses received from the meter during the dosing • 1:n function (pulse divider), at each signal from the pulse supp emitting meter the pump delivers a dosing product injection • ml x I, at each signal from the pulse supply emitting meter pump delivers a specific amount of the dosing product in “ml” (millilitres), corresponding to the value set during programming phase • l x I function, at each signal from the pulse supply emitting meter the pump delivers a specific am of dosing product in “l” (litres), corresponding to the value set during the programming phase • ml x m3

Open the catalog to page 1
eOne MF - 2

function, at each signal from the pulse supply emitting meter which indicates the transition of l m3 of fluid, the pump delivers a specific amount of dosing products in “ml” (millilitres), corresponding to the value set during the programming phase • ppm function, the dosing pump makes the necessary calculations and doses the exact amount of ppm (parts per million) set during the programming phase • mA function, the pump doses in a proportionally to the current signal (usually 4..20mA) riceived by a flow meter or another connected device • timer/ programmer function • UNDERLOAD – Suction...

Open the catalog to page 2

All Etatron D.S. catalogs and technical brochures

  1. BT-BTB MA/M

    7 Pages

  2. BT MA/AD

    7 Pages

  3. PKX MA/A

    6 Pages

  4. PKX FT/A

    5 Pages

  5. DLX CC/M

    7 Pages

  6. DLX MA/MB

    6 Pages

  7. DLX MA/AD

    7 Pages

  8. eOne MA

    2 Pages

  9. eOne PLUS

    2 Pages

Archived catalogs

  1. PKX FT/A

    5 Pages

  2. PKX MA/A

    6 Pages

  3. PKX MA/A

    6 Pages