High-End PowerPC QorIQ CPU • NXPTM PowerPC QorIQ T1022, 1.2 GHz, 64-bit architecture, Double Precision Floating Point Unit, Ethernet, ECC-RAM • Altera® Cyclone V FPGA for VME interface • RTC with battery backup • I/O interfaces designed to be compatible with Motorola CPU MVME5110 Wide Range of Software Support • OS-9, QNX®, VxWorks® and Linux® BSPs available • Universal boot loader: “Das U-Boot” • EtherCAT® master available • Low power CPU QorIQ T1014 (one core) • Extended MRAM (2 Mbyte instead of 512 kbyte) • Additional serial MRAM (512 kbyte) • Extended DDR3 RAM (2 Gbyte instead of 512 Mbyte) • Extended Flash memory (2x 128 Mbyte instead of 2x 16 Mbyte) • Gold Cap (backup time 7 days) instead of battery • Board version suitable for extended temperature range -40 °C ... +70 °C • P0 (pinning according VITA 35 P4V0-64 or customized, e. g.: Ethernet, serial, PMC Slot2 J4) • More customized solutions on request The VME-CPU/T10 is a VMEbus CPU board with 2 XMC/PMC slots. The NXP PowerPC QorIQ T1022 with 1.2 GHz features two 64-bit e5500 Power Architecture® processor cores with high-performance data path acceleration architecture (DPAA) and network peripheral interfaces. The local memory bus is 64 bits wide plus 8 bits ECC with an overall capacity of 512 Mbyte. 16 Mbyte SPI Flash for boot loader and 32 kbit IC EEPROM for U-Boot environment offer non-volatile memory spaces. The VME-CPU/T10 is equipped with a second 16 Mbyte backup SPI Flash selectable by jumper that can be used for system recovery, if a system crash occurs during a firmware update. VMEbus Interfaced by FPGA The Altera Cyclone V FPGA is connected to the CPU by PCI Express® for high bandwidth data exchange. The VMEbus master interface offers a A16/A24, D16/ D8 (EO) and an SGL arbiter. A VMEbus slave interface is not supported. XMC/PMC Interfaces The XMC1 interface comes with 1 lane PCIe bus and the XMC2 interface with 4 lane PCIe bus. They are designed according to VITA 42.3. Both PMC interfaces support 32-bit/66 MHz PCI bus according to PCI Local Bus Specification 3.0. The Flash memory carries the standard boot program “Das U-Boot” and enables the VME-CPU/T 10 to boot various operating systems from on-board Flash or network. BSPs from esd are available for OS-9, QNX, Linux and VxWorks. The esd EtherCAT master stack is available for all supported operating systems. Customization on Request CPU Type The vMe-CPU/T 10 is also available with the power saving single core QorlQ CPU T1014 with 1 lane PCIe (therefore only one XMC interface) on request. The memory can be extended with larger MRAM, DDR3 RAM and Flash. An additional serial MRAM is also available. Instead of the battery a Gold Cap can be equipped. Extended Temperature Range If an extended temperature range is requested please ask for the -40 °C ... +70 °C version of the VME-CPU/T10. Special P0 Pin Routing A special P0 pin routing according to VITA 35 P4V0-64 or customized routings, e.g. Ethernet, serial or PMC Slot2 J4 are available on request. All these options are available for customized serial production in reasonable quantities. Please contact our sales team for detailed information. Gigabit Ethernet The VME-CPU/T 10 is equipped with two Gigabit Ethernet interfaces accessible at the front panel. One of the Ethernet interfaces can be routed to VME P2 (100 Mbit/s only). Console (Serial) An RS-232 interface is accessible via an RJ45 connector at the front panel and additionally via VME P2 connector. Software Support esd electronics gmbh Vahrenwalder Str. 207 30165 Hannover / Germany

VME-CPU/T10 VME Master with 64-bit PowerPCTM T1022, XMC/PMC Slots FPGA FPGA Cyclone CycloneVV USB EEPROM EEPROM Boot Boot EEPROM EEPROM ENV ENV Temperature Sensors PCIe/PCI PCIe/PCI Bridge Bridge DCDCConverter Converter VCC MRAM MRAM Parallel Parallel SPI-Flash SPI-Flash Technical Specifications: Microcontroller and Memory: Microcontroller NXP PowerPCTM QorIQ T1022, 64-bit, Dual Core e5500, 1.2 GHz, Double Precision FPU General(continued): Relative humidity Power supply voltage 0% ... 90 % (non-condensing) VME 5 V, PIN_5V_MAX = 15 W, 3.3 V for XMC/PMC slots (if supported by VME 3.3V, otherwise...