DN-DP PROFIBUS® DP / DeviceNetTM Gateway Fast and Reliable Linking PROFIBUS DP and DeviceNet with Data Buffering • DeviceNet-PLC link, e.g. to SIEMENS S7-1500, S7-1200, S7-400, S7-300 • DeviceNet slave device with up to 240 user data bytes per direction, but limited to a total of 312 user data bytes if using both directions • Up to 40 DeviceNet slave devices can be addressed • Operation as DeviceNet scanner or slave Up to a total of 312 user data bytes can be configured for each DeviceNet slave device. For each direction up to 240 user data bytes can be set up. Configuration of the DN-DP Gateway as a Single DeviceNet Slave The DN-DP gateway can be configured as exactly one DeviceNet slave. With this configuration, it can be connected to exactly one DeviceNet scanner. Applications With the DN-DP gateway you can couple DeviceNet modules to e.g. a SIMATIC-S7. Approved Reliability and Ease of Use • PROFIBUS DP and DeviceNet interfaces are electrically isolated • DIN-EN rail mountable housing (TS 35) Configuration via the Configuration Tool of the PROFIBUS DP Master Linking DP and DeviceNet The DN-DP module can link any PROFIBUS DP master to a DeviceNet network. The DNDP gateway operates as a PROFIBUS DP slave-I/O component. At the DeviceNet network the DN-DP gateway can operate as a scanner to control several DeviceNet slave devices or as a single slave device to be connected to one DeviceNet scanner. The DN-DP module is always configured via a PROFIBUS DP master. Configuration of the DN-DP Gateway as a DeviceNet Scanner As a DeviceNet scanner, several DeviceNet slave devices can be addressed. The maximum number is between 20 and 40. This number depends on the configured PROFIBUS DP slave I/O type of each DeviceNet slave device. Physical Interfaces The DN-DP supports all DeviceNet compatible bit rates. The PROFIBUS DP Slave interface automatically recognizes all usual bit rates up to 12 Mbit/s. The PROFIBUS DP as well as the DeviceNet interface are electrically isolated. Configuration The module can be configured via PROFIBUS configuration tool, e.g. the PLC SIMATIC Manager or the TIA Portal. Electrical Isolation Physical Layer DeviceNet Coding Switches for DP-Address Voltage Controller Serial EEPROM Flash EPROM Electrical Isolation Technical Specifications: CPU: Microcontroller PowerPCTM 405 EP, 133 MHz Memory 4 M x 32 bit SDRAM (16 MB), 512 k x 16 bit Flash EPROM (1 MB) DeviceNet: CAN controller SJA1000, ISO11898-1 (CAN 2.0) DeviceNet interface According to DeviceNet Specification release 2.0, differential, electrically isolated, all DeviceNet bit rates are supported PROFIBUS DP: DP controller VPC3, DP-Slave DP interface RS-485, electrically isolated, max. 12 Mbit/s ©2017 esd electronic system design gmbh, Hannover DN-DP_Datasheet_en_04.odt All data are subject to change without prior notice. Rev.: 0.4 • Date: 2017-03-27 General: Ambient temperature 0 °C ... +50 °C Relative humidity Max. 90 % (non-condensing) Power supply Connectors 24 VDC, I24VTYPICAL = 140 mA, I24VMAX = 150 mA DeviceNet: 5-pin socket connector DP: DSUB9 female Power: 4-pin spring-cage connection plug Order Information: Hardware DN-DP Gateway DeviceNet / PROFIBUS DP-Slave, ISO11898-2, GSD-file CiA® and CANopen® are registered EU trademarks of CAN in Automation e.V.. All trademarks are reserved by their respective owners. esd electronic system design gmbh Vahrenwalder Str. 207 30165 Hannover / Germany